Instrument cluster (J285)
The cluster J285 holds the CAN gateway and the immobiliser as well as the gauges. With the owner's RB4 pinout, checked pin by pin against the factory manual.
Check first
Generated from the wiring data for this system’s 83 diagrams (listed under In the wiring data): the fuses, the ground points and the supply and ground pins of its control modules. These lists are not checked by hand, whatever the article's own status: each line says how it was worked out. Check anything important against the manual sheet before you cut or splice.
Fuses
| Fuse | Rating | Terminal | Where | Feeds here |
|---|---|---|---|---|
S1 | 10 A | 30 | Panel to 2005 MY: no. 1 p. 1113 Panel from 2006 MY: no. 1 p. 1117 | E87 J255 |
S5 | 10 A | 15 | Panel to 2005 MY: no. 5 p. 1113 Panel from 2006 MY: no. 5 p. 1117 | E272 F189 G266 J401 J446 J526 R36 |
S7 | 10 A | 15 | Panel to 2005 MY: no. 7 p. 1113 Panel from 2006 MY: no. 7 p. 1117 | J104 |
S8 | 5 A | 30 | Panel to 2005 MY: no. 8 p. 1113 Panel from 2006 MY: no. 8 p. 1117 | J526 R36 |
S10 | 5 A | 15 | Panel to 2005 MY: no. 10 p. 1114 Panel from 2006 MY: no. 10 p. 1118 | E102 J431 |
S11 | 5 A | 15 | Panel to 2005 MY: no. 11 p. 1114 Panel from 2006 MY: no. 11 p. 1118 | J234 |
S13 | 10 A | 30 | Panel to 2005 MY: no. 13 p. 1114 Panel from 2006 MY: no. 13 p. 1118 | J527 |
S15 | 10 A | 30 | Panel to 2005 MY: no. 15 p. 1114 Panel from 2006 MY: no. 15 p. 1118 | J285 J401 |
S17 | 10 A | 30 | Panel to 2005 MY: no. 17 p. 1114 Panel from 2006 MY: no. 17 p. 1118 | J446 |
S224 | 20 A | 30 | Panel to 2005 MY: no. 24 p. 1114 Panel from 2006 MY: no. 24 p. 1118 | J393 |
S226 | 30 A | 30 | Panel to 2005 MY: no. 26 p. 1114 Panel from 2006 MY: no. 26 p. 1118 | E87 |
S227 | 30 A | 30 | Panel to 2005 MY: no. 27 p. 1114 Panel from 2006 MY: no. 27 p. 1118 | J345 |
S228 | 20 A | 87 | Panel to 2005 MY: no. 28 p. 1115 Panel from 2006 MY: no. 28 p. 1118 | J538 |
S231 | 15 A | 15 | Panel to 2005 MY: no. 31 p. 1115 Panel from 2006 MY: no. 31 p. 1119 Panel from 2006 MY: no. 31 p. 1119 | J217 |
S236 | 30 A | 75x | Panel to 2005 MY: no. 36 p. 1115 Panel from 2006 MY: no. 36 p. 1119 Panel from 2006 MY: no. 36 p. 1119 | J519 |
S237 | 30 A | 75x | Panel to 2005 MY: no. 37 p. 1115 Panel from 2006 MY: no. 37 p. 1119 | J519 |
S238 | 15 A | 30 | Panel to 2005 MY: no. 38 p. 1116 Panel from 2006 MY: no. 38 p. 1119 | G303 J393 |
S239 | 20 A | 30 | Panel to 2005 MY: no. 39 p. 1116 Panel from 2006 MY: no. 39 p. 1119 | J401 J402 J503 R R94 |
S241 | 30 A | 30 | Panel to 2005 MY: no. 41 p. 1116 Panel from 2006 MY: no. 41 p. 1120 | J364 |
S242 | 25 A | 30 | Panel to 2005 MY: no. 42 p. 1116 Panel from 2006 MY: no. 42 p. 1120 | J104 |
S243 | 15 A | 15 | Panel to 2005 MY: no. 43 p. 1116 Panel from 2006 MY: no. 43 p. 1120 | J220 J623 |
S244 | 30 A | Panel to 2005 MY: no. 44 p. 1116 Panel from 2006 MY: no. 44 p. 1120 | J255 |
Ground points
| Point | Where |
|---|---|
135 | Splice inside the instrument panel wiring harnesssheet legend |
269 | Splice inside the instrument panel wiring harnesssheet legend |
Supply and ground pins
Terminal 30 (permanent positive), 15 (ignition), 75 (off while cranking) and 31 (ground) pins of the control module, from the wire labels. A pin opens its wire, traced to the fuse or ground point; open a module for all its pins.
J285 Control module with indicator unit in instrument panel insert · 4 pins
The instrument cluster (Audi’s term is “dash panel insert”, factory code J285) does more than show gauges on the B6. It also contains the CAN gateway and the immobiliser. That makes it the hub of the car’s electronics, and a faulty or swapped cluster affects far more than the dials.
What SSP 254 says (B6 at launch)
Section titled “What SSP 254 says (B6 at launch)”
Figure: SSP 254
Versions and display
Section titled “Versions and display”There are two versions:
- lowline;
- highline, with a high-quality colour centre display for the driver information system. It is fitted to cars with navigation or telematics.
The optional driver information system adds the radio clock, the Auto-Check system and the on-board computer. Every cluster shows the fuel range.
The radio-clock receiver sits in the rear bumper, for reception. The manual’s code for it is J489. The database’s location for it is only a guess from its name, so trust SSP 254 here.
The centre display can be driven from the control switch in the centre console only on cars with navigation (highline only), telematics, auxiliary heater and/or tyre-pressure monitoring. In the 12.2005 manual this switch is E272 “Board Computer Function Selector Switch II” (see the pinout below).
Built-in functions
Section titled “Built-in functions”- Gateway. The cluster links the drive, convenience and infotainment CAN buses. During diagnosis it checks communication with every CAN control unit and stores communication faults; current bus status is in its measured-value blocks. See CAN bus.
- Immobiliser III. It is integrated in the cluster and reads the key through the coil D2 around the ignition lock. It exchanges data with the convenience control unit J393 over the convenience CAN. The anti-theft alarm, for example, is triggered if the key used is not stored in the immobiliser.
- Turn-signal tick. It comes from an acoustic relay inside the cluster. The lamps themselves are switched by J519.
- Bulb-failure display. Auto-Check shows which bulb has failed and where on the car. J519 sends the message over the convenience CAN.
- Oil level. The minimum and maximum oil level since the last service can be read in the measured-value blocks.
- Plausibility checks. The cluster checks the two fuel senders on quattro models, and the terminal 15 input. Ignition-switch information also arrives as a CAN message from the steering column electronics J527.
- Mileage after replacement. After a cluster is replaced, the odometer reading can be adapted (several attempts allowed) until the new cluster has recorded 5 km.
- Coding source for other units. The automatic air conditioner codes itself from the cluster, the radios get vehicle identification and “convenience coding” from it, and the auxiliary heater’s start time is programmed through it.
Fuel gauge senders
Section titled “Fuel gauge senders”
Figure: SSP 254
The quattro has two senders:
The cluster reads each one separately, converts both to litres and adds them together. Front-wheel-drive cars have sender G only.
In the wiring manual:
| Sender | Signal | Ground |
|---|---|---|
| G | pin 2 (li/sw) to T32/3 | pin 3 (br/ge) to the cluster’s sensor ground T32/32 |
| G169 | pin 2 (li/sw) to T32/11 | shared sensor ground |
On some B7 engines the fuel-gauge line passes the fuel pump control module J538 connector (diagram 109).
Sender resistance (owner’s note). The gauge is analogue and works on resistance: the sender connects the signal pin to ground through a variable resistance.
| Tank | Resistance |
|---|---|
| Empty | 395–305 Ω as written in the owner’s sheet; almost certainly meant as 305–395 Ω |
| Full | 56–68 Ω |
Neither SSP 254 nor the 12.2005 wiring manual gives sender resistances, so these values are unverified. Measure between the sender’s signal and ground pins with the connector unplugged.
Owner’s notes: RB4 and RB8 clusters
Section titled “Owner’s notes: RB4 and RB8 clusters”From the site owner’s notes (not checked against factory documentation):
| B6 | B7 | |
|---|---|---|
| Cluster | Bosch RB4. This is the only cluster type the owner knows of in the B6 | Bosch RB8 |
| Immobiliser | Immo 3 | Immo 4 |
The B6 entry matches SSP 254, which states that the launch cluster contains “immobiliser III”.
The B7 standard-equipment diagrams (62, 109) still draw J285 with the same blue T32 and green T32a connectors. They also keep the same core pins:
- sender inputs;
- the three CAN buses;
- the immobiliser coil on T32/30–31;
- terminal 15/30/61.
The pinout below is the owner’s RB4 pinout. For an RB8, check each pin against the B7 diagram before relying on it.
RB4 pinout, cross-checked
Section titled “RB4 pinout, cross-checked”The RB4 has two 32-pin connectors.
| Connector | Colour | Part number (owner’s sheet) |
|---|---|---|
| T32 | blue | 1J0 972 977 H |
| T32a | green | 1J0 972 977 C |
The 12.2005 manual’s legends agree on the colours (“T32 – 32-pin connector, blue” and “T32a – 32-pin connector, green”, for example on manual p. 92). One legend, on p. 833, calls T32a blue as well, which is a manual typo. The part numbers are not in the manual.
| Blue T32 | Green T32a |
|---|---|
![]() |
![]() |
Figures: Owner’s pinout sheet
The “Factory manual” column shows what the wiring database has for that pin. In the manual the cluster is drawn as J285 with sub-symbols such as G1 (fuel gauge), G3 (coolant gauge), G21 (speedometer), K2 and K75 (warning lamps), so all of these were merged. Colours use the manual’s German abbreviations (see Wire colours and terminals).
The “Agrees?” column uses these values:
- Yes: same function.
- Partly: the same wire, but the manual names it differently or less precisely.
- Unclear: the manual neither supports nor contradicts the owner’s function.
- Not in manual: no wire drawn on that pin in any diagram.
No pin was found where the manual clearly contradicts the owner’s sheet.
Blue connector T32
Section titled “Blue connector T32”| Pin | Owner’s sheet | Factory manual (colour → other end) | Agrees? |
|---|---|---|---|
| 1 | Washer fluid low | br/ro → F77 washer fluid level warning switch | Yes |
| 2 | Coolant level low | bl/ge → F66 coolant level warning switch | Yes |
| 3 | Fuel gauge sender | li/sw → G fuel gauge sender, pin 2 | Yes |
| 4 | Coolant temperature | bl/br → G2 coolant temperature sensor | Yes |
| 5 | Control group 2 NAV | gn → E272 pin 2 (centre-console function selector switch) | Partly: the manual does not label this contact |
| 6 | Control group 3 NAV | gn/gr → E272 pin 3 | Partly: the manual does not label this contact |
| 7 | Control group x telematics | ge/ws → E272 pin 11, contact labelled “Telematik” | Yes |
| 8 | Menu switch | ge/gn → E272 pin 1, contact labelled “Menü” | Yes |
| 10 | Bonnet switch | br/li → F266 bonnet switch (also to J393) | Yes |
| 11 | Fuel gauge sender 2 (quattro only) | li/sw → G169 fuel level sensor 2 | Yes |
| 12 | Menu switch out A | ge/bl → E272 pin 6, “Out A” | Yes |
| 16 | FDR/TCS (= ESP) | gr/ro → J104 ABS/ESP control unit | Yes |
| 17 | Convenience CAN H | or/gn, comfort CAN high | Yes |
| 18 | Convenience CAN L | or/br, comfort CAN low | Yes |
| 19 | Infotainment CAN L | or/br, infotainment CAN low | Yes |
| 20 | Infotainment CAN H | or/li, infotainment CAN high | Yes |
| 21 | Ambient temp input | ge/gr → F38 “ambient temperature switch” | Yes. The manual calls the part a switch, not a sensor |
| 22 | S contact | ro → ignition switch terminal 86s (also J527 T16a/14) | Yes |
| 23 | Oil level / oil temp | ro/gr → G266 oil level/temperature sender | Yes |
| 24 | Self-levelling suspension | – | Not in manual |
| 25 | Menu switch enter | ws/br → E272 pin 8, “Enter” | Yes |
| 28 | Menu switch out B | gn/li → E272 pin 7, “Out B” | Yes |
| 30 | Transponder 2 | sw → D2 immobiliser coil, pin 2 | Yes |
| 31 | Transponder 1 | gn → D2 pin 1 | Yes |
| 32 | Terminal 31 (sensor) | br/ge, sensor ground for G, G169, F38, F66, F77 and E272 | Yes |
Pins 9, 13–15, 26, 27 and 29 are empty in both the owner’s sheet and the manual.
Green connector T32a
Section titled “Green connector T32a”| Pin | Owner’s sheet | Factory manual (colour → other end) | Agrees? |
|---|---|---|---|
| 1 | Terminal 58d | gr/ge → F189 tiptronic switch, pin 8 (automatic only). The signal is not named | Unclear. A 58d dimming feed to the selector-display lighting would fit, but the manual does not say so |
| 2 | Terminal 30 | ro/bl → fuse S15, terminal 30 | Yes |
| 3 | Terminal 15 | sw → ignition switch terminal 15 (fuse S5) | Yes |
| 5 | Speedometer input | br/ro → G22 speed sender / J217 (B6 diagrams) | Yes |
| 6 | Speedometer output 2 | – | Not in manual |
| 7 | Airbag (inverted) | ws/ge → J234 (airbag lamp K75 line) | Yes. “Inverted” is not stated in the manual |
| 8 | Right turn signal | – | Not in manual |
| 9 | Brake fluid low | ge/bl → F34 brake fluid level warning switch | Yes |
| 10 | Left turn signal | – | Not in manual |
| 11 | Trailer turn signal | – | Not in manual |
| 12 | CAN drive L | or/br, drive CAN low | Yes |
| 13 | CAN drive H | or/sw, drive CAN high | Yes |
| 14 | Terminal 61 / charge warning | bl → alternator D+ (terminal 61) | Yes |
| 16 | Oil pressure 2 | ws/gr → F1 oil pressure switch | Yes |
| 17 | Terminal 58s | gr/bl, dimmed switch illumination (58s) | Yes |
| 18 | Terminal 31 load | br → ground | Yes |
| 19 | Terminal 31 load | br → ground | Yes |
| 21 | Speedometer output 1 | ws/bl, vehicle speed signal → J104, navigation, phone | Yes |
| 22 | ABS warning | sw/ro → J104 | Yes |
| 23 | K wire | gn/ro, K-line to the diagnostic socket | Yes |
| 24 | CAN drive (display) | – | Not in manual |
| 25 | Tank flap switch | – | Not in manual |
| 26 | CAN diagnosis L | – | Not in manual |
| 27 | CAN diagnosis (display) | – | Not in manual |
| 28 | CAN diagnosis H | – | Not in manual |
| 29 | Headlight range control | bl/ws → J431 headlight range control module | Yes |
| 30 | Belt buckle | gr/sw → E24 driver’s belt switch | Yes |
| 31 | External buzzer | – | Not in manual |
| 32 | Brake pad wear | br/gn → G35, and G34 on the same circuit | Yes |
Pins 4, 15 and 20 are empty in both.
What the cross-check shows
Section titled “What the cross-check shows”- 40 pins agree and 2 partly agree (T32/5 and /6, which run to the centre-console switch E272 without a function label in the manual). T32a/1 is unclear. None contradict the owner’s sheet.
- 11 owner pins are not drawn in the 12.2005 manual:
- T32/24;
- T32a/6, 8, 10, 11, 24–28 and 31. The manual covers only the equipment it has diagrams for, so a missing pin does not mean the owner is wrong. These functions are unverified.
- Pins that appear only in B6 diagrams:
- The “Terminal 31 (sensor)” pin T32/32 should only carry sensor grounds. Never use it as a ground for added loads. Use T32a/18–19 (load ground) or a body ground point.
In the wiring data
Everything drawn in this system’s diagrams of the factory manual, generated when the site is built. A part drawn in several systems is listed on each of them. Locations say how they were worked out; the component pages have every pin.
Control modules
Other components
Alternator (2)
Ignition switch (2)
Lamp (8)
L15Ashtray LightL67Left Instrument Panel Vent IlluminationL68Center Instrument Panel Vent IlluminationL69Right Instrument Panel Vent IlluminationL120Storage Compartment IlluminationL121Cup Holder IlluminationL122Coin Holder IlluminationL157Illumination for center armrest
Radio / antenna (4)
Sensor (8)
GSender for fuel gaugeG2Engine Coolant Temperature (ECT) SensorG22Speedometer Vehicle Speed Sensor (Camshaft Position (CMP) Sensor, on transmission)G35Right Front Brake Pad Wear SensorG169Fuel Level Sensor 2G266Oil Level Thermal SensorG294Brake Booster Pressure SensorG303Radar Interior Monitoring Control Module 1
Switch (12)
E1Light switchE24Left Seat Belt SwitchE87A/C Control HeadE102Headlight AdjusterE272Board Computer Function Selector Switch IIF1Oil Pressure SwitchF34Brake Fluid Level Warning SwitchF38Ambient Temperature SwitchF66Engine Coolant Level (ECL) Warning SwitchF77Windshield Washer Fluid Level Warning SwitchF189Tiptronic SwitchF266Front Hood Switch
Splices
327Sensor groundA2Ignition-switched positive (terminal 15)A17Alternator charge warning (terminal 61, D+)A21Key-in-ignition signal (S contact, terminal 86s)A27Vehicle speed signalA50Battery positive via comfort system (terminal 30as)A76K-line (diagnosis)A121Drivetrain CAN HighA122Drivetrain CAN LowA146Comfort CAN HighA147Comfort CAN LowA175Dimmed switch illumination (terminal 58s)A178Infotainment CAN HighA179Infotainment CAN LowB270Dimmed switch illumination (terminal 58s)D66Alternator charge warning (terminal 61, D+)D159Drivetrain CAN HighD160Drivetrain CAN LowD166K-line (diagnosis)
Diagrams
- 3 Basic Equipment Lowline (B6 only)
- 4 Basic Equipment Highline (B6 only)
- 6 Comfort system (B6 only)
- 7 6-speed automatic transmission 09L with Tiptronic (B6 only)
- 9 3.0 l - Injection Engine (162 kW - Motronic - 6 Cylinder) engine code AVK, BGN (B6 only)
- 10 1.8 l - Injection Engine (125 kW - Motronic - 4 Cylinder) engine codes AMB (B6 only)
- 12 4.2 l - Injection Engine (253 kW - Motronic - 8 Cylinder) engine code BHF (B6 only)
- 14 ABS, with ESP (4.2 l - Injection Engine) (B6 only)
- 18 Basic Equipment Lowline (B6 only)
- 19 Basic Equipment Highline (B6 only)
- 20 Automatic Day/Night Interior Mirror (B6 only)
- 25 Constantly variable automatic transmission, multitronic® 01J (B6 only)
- 26 5-speed automatic transmission with Tiptronic (B6 only)
- 29 Automatic Day/Night Interior Mirror (B6 only)
- 30 CAN-Bus wiring (B6 only)
- 32 Garage Door Opener - "Homelink" (B6 only)
- 33 Cellular Telephone - Preparation on the Middle Console (B6 only)
- 34 Automatic Climate Control (B6 only)
- 35 Comfort system (B6 only)
- 36 Radio (B6 only)
- 37 Radio / Navigation system (RNS-D) (B6 only)
- 38 Headlight with high intensity gas discharge lamp and automatic headlight adjuster (B6 only)
- 39 Heated seats, heated steering wheel (B6 only)
- 40 Heated seats, heated steering wheel (B6 only)
- 43 6-speed automatic transmission 09L with Tiptronic (B6 only)
- 50 Power Rear Window Shade (B7 only)
- 52 Anti-Lock Brake System (ABS) with Electronic Differential Lock (EDL), Anti-Slip Regulation (ASR), Electronic Brake Pressure (B7 only)
- 53 Avant, rear wiring (B7 only)
- 54 Airbags and Safety Belt Tensioners (B7 only)
- 56 Automatic Climate Control (B7 only)
- 58 Parking Aid (B7 only)
- 60 Automatic Day/Night Interior Mirror (with Light Sensor and coming/leaving home function) (B7 only)
- 61 Data Link Connector (DLC) (B7 only)
- 62 Standard Equipment (B7 only)
- 63 Headlights with High Intensity Gas Discharge (HID) "Bi-Xenon" lamps and Automatic Headlight Beam Adjusting (B7 only)
- 64 Headlights with High Intensity Gas Discharge (HID) "Bi-Xenon" lamps, Cornering Light and Automatic Headlight Beam (B7 only)
- 67 Comfort system (B7 only)
- 68 Headlight (B7 only)
- 69 Tire Pressure Monitoring System (B7 only)
- 72 Multi-function steering wheel (B7 only)
- 73 Headlights with High Intensity Gas Discharge (HDI) Lamp and Automatic Headlight Beam Adjusting (B6 only)
- 78 2.0 l - TFSI - Injection Engine (147 kW - Motronic - 4 Cylinder), engine codes BGB, BPG (B7 only)
- 86 6-speed automatic transmission 09L with Tiptronic (B7 only)
- 87 Automatic Transmission, multitronic 01J, from November 2004, Automatic Transmission, multitronic 0AN (B7 only)
- 89 4.2L - Injection Engine (253 kW - Motronic - 8 Cylinder) engine codes BBK, BHF (B7 only)
- 95 3.2L - FSI - Injection Engine (188 kW - Motronic - 6 Cylinder) engine codes AUK, BKH (B7 only)
- 102 4,2 l - FSI - Injection Engine (309 kW - Motronic - cylinder 8) engine code BNS (B7 only)
- 104 Anti-Lock Brake System (ABS) with Electronic Differential Lock (EDL), Anti-Slip Regulation (ASR), Electronic Brake Pressure (B7 only)
- 105 Airbags and Safety Belt Tensioners (B7 only)
- 109 Standard Equipment (B7 only)
- 110 Comfort System (B7 only)
- 111 Can-Bus wiring (B7 only)
- 112 Multi-function steering wheel (B6 and B7)
- 113 RS Sport Steering Wheel (B7 only)
- 116 Power seats with lumbar support and electrically seat heating (B7 only)
- 118 Radio / Navigation System RNS-Low (B7 only)
- 119 Radio / Navigation system (RNS-E) - Satellite Radio (B7 only)
- 120 Radio Systems (Symphony II, Bose®) - Satellite Radio (B7 only)
- 121 Cellular Telephone - Preparation (B7 only)
- 126 Cellular Telephone - Preparation with Hands Free Control Module (B7 only)
- 127 Radio (B7 only)
- 128 4,2 l - FSI - Injection Engine (309 kW - Motronic - cylinder 8) engine code BNS (B7 only)
- 129 Telematic without voice control (only for USA) (B6 only)
- 302 Basic Equipment Highline (B6 only)
- 303 3.0 l - Injection Engine (162 kW - Motronic - 6 Cylinder) engine code AVK (B6 only)
- 304 1.8 l - Injection Engine (125 kW - Motronic - 4 Cylinder) engine codes AMB (B6 only)
- 305 Telematic without voice control (only for USA) (B6 only)
- 307 Airbag for driver, passenger with seat belt tensioner and side Airbag (B6 only)
- 309 ABS, with ESP (B6 only)
- 311 Avant, rear (B6 only)
- 312 Diagnostic connection (B6 only)
- 313 Electric window shade (B6 only)
- 316 Cellular Telephone - Preparation on the Middle Console (B6 only)
- 317 Automatic Climate Control (B6 only)
- 318 Comfort system (B6 only)
- 321 Multi-function steering wheel (B6 only)
- 322 Navigation system NS-LOW (B6 only)
- 323 Radio (B6 only)
- 325 Headlight with high intensity gas discharge lamp and automatic headlight adjuster (B6 only)
- 327 Servotronic (B6 only)
- 329 Front and rear heated seat with and without steering wheel heater (B6 only)
- 331 CAN-Bus wiring (B6 only)
- 333 Garage Door Opener - "Homelink" (B6 only)
Related articles
Modify
Understand
- B6 vs B7 electrical differences
- CAN bus basics (SSP 238)
- Drivetrain and convenience CAN (SSP 269)
- Vehicle electrical system (J519, J527, MCB)
Look up
Part numbers in this article
| Number | Name in the catalogue | Illustrations |
|---|---|---|
1J0 972 977 H | Not in the loaded part of the catalogue. The link decodes the number. | |
1J0 972 977 C | Not in the loaded part of the catalogue. The link decodes the number. | |
The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
G | Sender for fuel gauge | B6 and B7 | Connector at Electrical harness connector |
G169 | Fuel Level Sensor 2 | B6 and B7 | Connector at Electrical harness connector |
G1 | Fuel Gauge | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
G3 | Engine Coolant Temperature (ECT) Gauge | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
G21 | Speedometer | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
K2 | Generator (GEN) Warning Light | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
K75 | Airbag Malfunction Indicator Lamp (MIL) | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
D2 | Induction Coil of Anti-theft Immobilizer | B6 and B7 | Steering column, around the ignition lock |
E272 | Board Computer Function Selector Switch II | B6 only | In the centre console, bottom |
F77 | Windshield Washer Fluid Level Warning Switch | B6 and B7 | Front, at the washer fluid reservoir |
F66 | Engine Coolant Level (ECL) Warning Switch | B6 and B7 | At the expansion tank |
G2 | Engine Coolant Temperature (ECT) Sensor | B6 and B7 | Part of Engine Coolant Temperature (ECT) Sensor -G62- |
F266 | Front Hood Switch | B6 and B7 | In lock carrier |
J104 | ABS Control Module (w/EDL) | B6 and B7 | In engine compartment, on hydraulic unit, front left |
F38 | Ambient Temperature Switch | B6 and B7 | Front end, behind the bumper |
G266 | Oil Level Thermal Sensor | B6 and B7 | At the bottom of the oil pan |
F34 | Brake Fluid Level Warning Switch | B6 and B7 | Wired into the wiring harness |
F1 | Oil Pressure Switch | B6 and B7 | Its wires run through T10 (Connector station on E-Box) |
J431 | Headlight Range Control Module | B6 and B7 | Behind glove box |
E24 | Left Seat Belt Switch | B6 and B7 | Wired into the airbag wiring harness |
G34 | Left Front Brake Pad Wear Sensor | B6 and B7 | At the front brake caliper |
G35 | Right Front Brake Pad Wear Sensor | B6 and B7 | At the front brake caliper |
J234 | Airbag Control Module | B6 and B7 | Below centre console, in front of handbrake lever |
J519 | Vehicle Electrical System Control Module | B6 and B7 | Behind driver's storage compartment |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
J489 | Radio Frequency Controlled Clock Receiver | B6 and B7 | Instrument panel centre / glove compartment |
F189 | Tiptronic Switch | B6 and B7 | Integrated in the printed circuit board in the symbol panel located in the shift mechanism cover |
G22 | Speedometer Vehicle Speed Sensor (Camshaft Position (CMP) Sensor, on transmission) | B6 only | Left of transmission |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 40–43 (dash panel insert); also pages 55, 62, 67–68 and 76.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseUsed to cross-check the RB4 pinout.
- A4 B6 – Pinouts / Wire Diagrams (owner's sheet) — Site ownerRB4 pinout, connector drawings, RB4/RB8 and fuel-sender notes. Not checked against factory documentation unless stated.
- Ross-Tech Wiki – Immobilizer — Ross-TechImmobiliser generations 3 and 4.

