Skip to content

Search is only available in production builds. Try building and previewing the site to test it out locally.

CAN bus in the A4 B6/B7

The A4 has three CAN buses joined by a gateway in the instrument cluster J285, and diagnosis over the K- and L-lines. Which modules sit on which bus, which wires and splices carry it, and where to measure.

Applies to: B6 and B7VerifiedFrom the factory manual or Audi training material.

Check first

Generated from the wiring data for this system’s 5 diagrams (listed under In the wiring data): the fuses, the ground points and the supply and ground pins of its control modules. These lists are not checked by hand, whatever the article's own status: each line says how it was worked out. Check anything important against the manual sheet before you cut or splice.

Fuses

FuseRatingTerminalWhereFeeds here
S110 A30Panel to 2005 MY: no. 1 p. 1113
Panel from 2006 MY: no. 1 p. 1117
E87 J255
S510 A15Panel to 2005 MY: no. 5 p. 1113
Panel from 2006 MY: no. 5 p. 1117
J401 J446 J526 R36
S710 A15Panel to 2005 MY: no. 7 p. 1113
Panel from 2006 MY: no. 7 p. 1117
J104
S85 A30Panel to 2005 MY: no. 8 p. 1113
Panel from 2006 MY: no. 8 p. 1117
J526 R36
S105 A15Panel to 2005 MY: no. 10 p. 1114
Panel from 2006 MY: no. 10 p. 1118
J431 V319
S115 A15Panel to 2005 MY: no. 11 p. 1114
Panel from 2006 MY: no. 11 p. 1118
J234
S1210 A30Panel to 2005 MY: no. 12 p. 1114
Panel from 2006 MY: no. 12 p. 1118
drawn in this system’s diagrams
S1310 A30Panel to 2005 MY: no. 13 p. 1114
Panel from 2006 MY: no. 13 p. 1118
J527
S1510 A30Panel to 2005 MY: no. 15 p. 1114
Panel from 2006 MY: no. 15 p. 1118
J285 J401
S1710 A30Panel to 2005 MY: no. 17 p. 1114
Panel from 2006 MY: no. 17 p. 1118
J446
S185 A15Panel from 2006 MY: no. 18 p. 1118V318
S2215 A30Panel to 2005 MY: no. 22 p. 1114
Panel from 2006 MY: no. 22 p. 1118
J386 J387
S22315 A30Panel to 2005 MY: no. 23 p. 1114
Panel from 2006 MY: no. 23 p. 1118
J388 J389
S22420 A30Panel to 2005 MY: no. 24 p. 1114
Panel from 2006 MY: no. 24 p. 1118
J393
S22630 A30Panel to 2005 MY: no. 26 p. 1114
Panel from 2006 MY: no. 26 p. 1118
E87
S22730 A30Panel to 2005 MY: no. 27 p. 1114
Panel from 2006 MY: no. 27 p. 1118
J345
S23115 A15Panel to 2005 MY: no. 31 p. 1115
Panel from 2006 MY: no. 31 p. 1119
Panel from 2006 MY: no. 31 p. 1119
J217
S23630 A75xPanel to 2005 MY: no. 36 p. 1115
Panel from 2006 MY: no. 36 p. 1119
Panel from 2006 MY: no. 36 p. 1119
J519
S23730 A75xPanel to 2005 MY: no. 37 p. 1115
Panel from 2006 MY: no. 37 p. 1119
J519
S23815 A30Panel to 2005 MY: no. 38 p. 1116
Panel from 2006 MY: no. 38 p. 1119
J393
S23920 A30Panel to 2005 MY: no. 39 p. 1116
Panel from 2006 MY: no. 39 p. 1119
J401 J402 J503 R R94
S24130 A30Panel to 2005 MY: no. 41 p. 1116
Panel from 2006 MY: no. 41 p. 1120
J364
S24225 A30Panel to 2005 MY: no. 42 p. 1116
Panel from 2006 MY: no. 42 p. 1120
J104
S24315 A15Panel to 2005 MY: no. 43 p. 1116
Panel from 2006 MY: no. 43 p. 1120
drawn in this system’s diagrams
S24430 APanel to 2005 MY: no. 44 p. 1116
Panel from 2006 MY: no. 44 p. 1120
J255

Ground points

PointWhere
135Splice inside the instrument panel wiring harnesssheet legend

Supply and ground pins

Terminal 30 (permanent positive), 15 (ignition), 75 (off while cranking) and 31 (ground) pins of the control module, from the wire labels. A pin opens its wire, traced to the fuse or ground point; open a module for all its pins.

J285 Control module with indicator unit in instrument panel insert · 4 pins
PinCarriesWireFuse / ground
T32/32Sensor groundstatedbr/ge269
T32a/3Ignition-switched positive (terminal 15)statedswS5 S10 S243
T32a/18Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr135
T32a/19Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr135

The A4 B6 and B7 have three separate CAN networks. They are joined by a gateway built into the instrument cluster (J285). The car has no separate gateway module: there is no J533 anywhere in the A4 wiring manual. Diagnosis still runs mainly over the old K-line and L-line. On the B7 the drivetrain CAN is also wired to the diagnostic connector.

For how CAN works in general, see CAN bus basics. For VW Group signal levels and the full fault-finding procedure, see Drivetrain and convenience CAN.

Bus Speed CAN-High wire CAN-Low wire Main splices What it carries
Drivetrain (“drive”, high-speed) 500 kbit/s or/sw (orange/black) or/br (orange/brown) A121 / A122, D159 / D160 Data about the running car, such as road speed, engine speed and coolant temperature. Engine, gearbox, ABS/ESP and airbag modules sit here.
Convenience (“comfort”, low-speed) 100 kbit/s or/gn (orange/green) or/br A146 / A147 Climate control, parking aid, tyre pressure, seat memory, door control units, central locking, onboard power control.
Infotainment (“display bus” in SSP 254, low-speed) 100 kbit/s or/li (orange/lilac) or/br A178 / A179 Radio, navigation, telephone interface.
Diagnosis K-line / L-line (B6, B7). B7 also has drivetrain CAN on the DLC — — A76 (K), A159 (L) Workshop tester access. See Diagnosis access.

The speeds come from SSP 254, which lists “Drive BUS 500 kBaud, Convenience BUS 100 kBaud, Display BUS 100 kBaud” for the A4. The wire colours come from the A4 wiring manual and match the VW Group colour rule in SSP 269 exactly (see Wire colours).

SSP 254 states that the A4’s dash panel insert contains “the gateway for linking the three data bus systems: drive, convenience, information” as well as immobiliser III. The wiring manual agrees: all three bus pairs end at the cluster J285. The B6 manual calls it “Control module with indicator unit in instrument panel insert”; the B7 manual calls it “Instrument Cluster Control Module”. The B7 diagrams also have no separate gateway, so the B7 still uses the cluster as gateway.

The gateway passes messages between buses. SSP 254 gives some A4 examples:

  • Bulb monitoring: the vehicle electrical system control module J519 sends a bulb-failure message over the convenience CAN to J285, which shows it on the centre display.
  • Steering column switches: the steering column electronics J527 code the stalk positions and send them over the convenience CAN to J519. J527 is on both the drivetrain and the convenience CAN.
  • Radio switch-on with the key (S-contact): J527 detects the key, sends this over the convenience CAN to the cluster (gateway), and the cluster passes it on to the radio over the infotainment CAN. If the radio does not switch on, SSP 254 suggests checking each link in that chain.
  • Diagnosis: because the cluster is the gateway, it checks communication with every module on the CAN during diagnosis. It stores communication faults in its fault memory and shows the live status in its measured value blocks.

Measure the buses at the cluster’s two connectors:

  • Blue T32: pin 17 convenience CAN-High, 18 convenience CAN-Low, 20 infotainment CAN-High, 19 infotainment CAN-Low.
  • Green T32a: pin 13 drivetrain CAN-High, 12 drivetrain CAN-Low, 23 K-line (on to the diagnostic connector pin 7).

The owner’s sheet also names T32a pins 24 and 26–28 (CAN drive and CAN diagnosis for a display); none of them is wired in the A4 manual, B6 or B7. Wire colours and splices are in the table above; the pin-by-pin check of the owner’s sheet against the manual is in Instrument cluster. Sources: B6 cluster CAN sheet (manual p. 263, p. 1067) and B7 (p. 712).

SSP 254 CAN networking diagram for the Audi A4 B6: the drive bus in green, convenience bus in blue, display/infotainment bus in yellow, K-wire in red and L-wire in brown, all meeting at the gateway in the instrument cluster J285

CAN networking of the A4 ’01, from SSP 254 p. 38 (© Audi AG). Green = drive bus, blue = convenience bus, yellow = display/infotainment bus, red = K-wire, brown = L-wire. This shows the launch spec. Some codes differ in the 2005 wiring manual: the auxiliary heater is J364 there, not J162, and J453, J499 and G85 do not appear in the manual.

The VW Group buses use a “tree” wiring layout: each module’s stub joins a common splice instead of the bus running from module to module (SSP 269). The A4 manual draws it the same way. Each bus has one splice pair in the instrument panel harness (A121/A122, A146/A147, A178/A179). The drivetrain bus has a second pair in the engine-compartment harness (D159/D160) that feeds the modules in the E-box and engine bay. The manual only gives these splice locations as “inside the instrument panel / engine compartment wiring harness”. It does not give a physical position.

The modules, data buses and power of a B6 (drawn for a 2004 1.8T with a 6-speed manual), checked against the factory wiring diagrams No. 30, 312, 804, 806 and 852. Select a block to open its page. Optional equipment is outlined dashed.

The instrument cluster J285 is the gateway joining the drivetrain, comfort and infotainment CAN buses; diagnostics reach the modules over a separate K-line from the OBD socket. POWER DRIVETRAIN CAN · 500 kbit/s COMFORT CAN · 100 kbit/s INFOTAINMENT CAN · 100 kbit/s DIAGNOSTICS K-line to engine, ABS, airbag, climate, comfort, electrical system and radio modules A BatteryABattery C AlternatorCAlternator B StarterBStarter D Ignition switchDIgnition switch Fuses & relays terminals 30 · 15 · X to every moduleFuses & relaysterminals 30 · 15 · X to every module J285 Instrument cluster · gatewayJ285Instrument cluster · gateway J220 Engine ECUJ220Engine ECU J104 ABS / ESPJ104ABS / ESP G85 Steering angle (no page: not a code of the wiring manual)G85Steering angle J234 AirbagJ234Airbag J431 Headlight rangeJ431Headlight range J393 Comfort centralJ393Comfort central J519 Electrical systemJ519Electrical system J527 Steering columnJ527Steering column E87 Climate controlE87Climate control J386 Driver doorJ386Driver door J387 Passenger doorJ387Passenger door J388/9 Rear doorsJ388/9Rear doors J136 Seat memoryJ136Seat memory J446 Parking aidJ446Parking aid R RadioRRadio J401 NavigationJ401Navigation J526 TelephoneJ526Telephone T16 OBD socketT16OBD socket
The instrument cluster (J285) is the gateway: the three CAN buses only meet there. The OBD socket reaches modules over the K-line, not CAN. Power Drivetrain CAN Comfort CAN Infotainment CAN K-line

The layers of the drawing:

  • Power (standard terminal numbering): every module gets battery voltage through the fuse panels, on one or more standard terminals: 30 permanent battery positive, 15 ignition-switched, X (75) switched but dropped while cranking, 50 start signal, 31 ground.
  • Drivetrain CAN (factory manual): high-speed two-wire bus at 500 kbit/s linking the engine, brakes and safety modules. It only works when both wires are intact. Wire colours orange/black (high), orange/brown (low), 0.35 mm². Splices A121 (high) and A122 (low) in the instrument panel harness; D159 / D160 in the engine compartment harness.
  • Comfort (convenience) CAN (factory manual): body electronics bus at 100 kbit/s: locking, windows, lights, steering column switches, climate. Wire colours orange/green (high), orange/brown (low), 0.35 mm². Splices A146 (high) and A147 (low) in the instrument panel harness. Also on this bus: trailer module J345 and auxiliary heater J364, if fitted. Bus type: low-speed fault-tolerant on this generation of VW/Audi, not stated in the manual.
  • Infotainment CAN (factory manual): radio, navigation and phone bus at 100 kbit/s. It lets the radio show text in the cluster display and receive ignition, illumination and speed information. Wire colours orange/lilac (high), orange/brown (low), 0.35 mm². Splices A178 (high) and A179 (low) in the instrument panel harness.
  • K-line diagnostics (factory manual): single-wire diagnostic line from pin 7 of the OBD socket (green/red). It runs to splice A76 in the instrument panel harness and on to the modules, including cluster pin T32a/23. Pin 15 carries the L-line (green/blue). The factory diagram shows no CAN at the socket. (The B7 differs: its drivetrain CAN is brought to the diagnostic plug.)

The blocks. “Manual” means checked against the factory wiring diagrams and component locations; “unverified” was not checked. Pin numbers are given only where they were read off the diagram page itself.

Block Bus Job Where Pins, wires and notes Basis
A Battery Power 12 V supply for the whole car. The main fuses sit on the battery. Plenum chamber, under the cowl at the back of the engine bay. unverified
C Alternator Power Charges the battery and feeds the electrical system while the engine runs. Front of the engine, belt-driven. unverified
B Starter Power Cranks the engine when terminal 50 is energised by the ignition switch. On the gearbox bell housing. unverified
D Ignition switch Power Switches terminal 15 (and X, 50) from the permanent terminal 30 feed. Steering column. Fed by two 2.5 mm² red wires on terminal 30; terminal 15 leaves on a 4.0 mm² black wire. manual
Fuses and relays Power Main fuses on the battery; fuse holder and relay carriers distribute battery voltage to each module and consumer. Fuse holder in the driver-side end of the instrument panel; relay carrier on the driver side of the instrument panel. Fuses from 23 onwards are numbered 223 onwards in the factory current flow diagrams. manual
J285 Instrument cluster, gateway All three CAN buses and K-line The interface between the CAN buses: it passes selected data from one bus to another. Also drives the gauges and the driver information display. Dashboard, behind the steering wheel. Green 32-pin (T32a): 13 drivetrain high (orange/black), 12 drivetrain low (orange/brown), 23 K-line (green/red). Blue 32-pin (T32): 20 infotainment high (orange/lilac), 19 infotainment low (orange/brown), 17 comfort high (orange/green), 18 comfort low (orange/brown). All three buses are present at these two plugs, the only place they can all be reached together. p. 263 manual
J220 Engine ECU Drivetrain CAN, K-line Motronic engine control: injection, ignition, boost, electronic throttle. Electronics box in the plenum chamber. The bus enters the electronics box through the red 17-pin connector T17d: 14 high (orange/black), 13 low (orange/brown). ECU pin numbers are in the engine diagram. The manual covers the US 1.8T (AMB), not the BFB, so check before relying on it. p. 262 manual
J104 ABS / ESP Drivetrain CAN, K-line Anti-lock brakes, electronic differential lock and stability control. Forms one unit with the hydraulic unit N55. Engine compartment, front left, on the hydraulic unit. 24 high (orange/black), 40 low (orange/brown). Routed through the black 17-pin connector T17 at the left A-pillar: 6 high, 5 low. p. 262 manual
G85 Steering angle Drivetrain CAN Steering angle sensor used by the ESP. In the return spring with slip ring on the steering column. Drawn in the factory diagrams together with the steering column module J527, which has its own drivetrain CAN connection. p. 10 manual
J234 Airbag Drivetrain CAN, K-line Airbag and belt tensioner control. Below the centre console, in front of the handbrake lever. 3 high (orange/black), 2 low (orange/brown). p. 262 manual
J431 Headlight range (optional) Drivetrain CAN Automatic headlight levelling. Only on cars with xenon headlights. Behind the glove box. Not shown in the factory CAN-bus diagram, so its bus connection here is unverified. Location is from the manual. unverified
J393 Comfort central Comfort CAN, K-line Central locking, remote key, alarm, interior lights, window convenience functions. At the sill panel, front left. p. 265 manual
J519 Electrical system Comfort CAN, K-line Vehicle electrical system control: exterior lighting, wipers, horn, bulb monitoring. Behind the driver’s storage compartment. CAN on the grey 32-pin connector T32b, pins 13 and 12 (high/low order not yet checked). p. 264 manual
J527 Steering column Comfort CAN and drivetrain CAN Steering column electronics: indicator and wiper stalks, horn, multifunction wheel. Connected to both the comfort and the drivetrain bus. At the steering column. Black 16-pin (T16a): 10 drivetrain high (orange/black), 11 drivetrain low (orange/brown), 9 comfort high (orange/green), 8 comfort low (orange/brown). p. 263 manual
E87 Climate control Comfort CAN, K-line Automatic climate control head. Called J255 Climatronic in other Audi documents. Centre console. p. 265 manual
J386 Driver door Comfort CAN Driver door module: window, mirror, lock, door switches. Integrated in the electric window motor in the door. Door wiring passes through the 10-pin connector station at the A-pillar. p. 265 manual
J387 Passenger door Comfort CAN Front passenger door module: window, mirror, lock. Integrated in the electric window motor in the door. manual
J388 / J389 Rear doors Comfort CAN Rear door modules: windows and locks. Integrated in the electric window motor in each rear door. manual
J136 Seat memory (optional) Comfort CAN Memory for the electric driver seat and mirrors. Only with memory seats. Driver seat, reached through the red 10-pin seat connector station. p. 265 manual
J446 Parking aid (optional) Comfort CAN Parking sensor control. Only with park distance control. Rear cross panel in the luggage compartment, left, behind the trim near the left rear light. p. 264 manual
R Radio Infotainment CAN, K-line Head unit (Chorus, Concert, Symphony). CAN arrives on the black 20-pin radio connector. Centre console. p. 268 manual
J401 Navigation (optional) Infotainment CAN Navigation unit with CD drive (NS-Low or RNS-E). Only if fitted. Centre console. p. 267 manual
J526 Telephone (optional) Infotainment CAN Telephone / telematics control module. Only if fitted. Not checked. p. 267 manual
T16 OBD socket K-line 16-pin diagnostic connector. Under the dashboard on the driver’s side. 1 ignition-switched +12 V (black/blue, 15 A fuse S231). 4 and 5 ground (brown). 7 K-line (green/red). 15 L-line (green/blue). 16 permanent +12 V (red/black, 10 A fuse S12). The factory diagram shows no CAN wires at this socket. p. 950 manual

Every block’s position in the car is on its page and in the 3D car. Two cautions with this drawing: the manual is the US-market edition, whose 1.8T is engine code AMB, not BFB, so engine-side wiring may differ; and equipment varies car to car. Confirm on the car with a meter before splicing. Sources: the factory manual’s diagrams No. 30, 312, 804, 806 and 852 (CAN-Bus wiring from 2004 m.y., diagnostic connection from 2002 m.y., control module locations); Audi SSP 343 excerpt: bus speeds; Audi repair manual: CAN-Bus system, function.

All of the following come from the wiring manual’s CAN diagrams. These are 30 (B6 from MY2004), 331 (B6 from MY2002) and 111 (B7 from MY2006), plus the individual system diagrams. “B6”/“B7” means the manual only shows that module, or its CAN wiring, for that generation. Many modules are optional.

Code Module Gen. Notes
J285 Instrument cluster (gateway) B6, B7 Green T32a/13 = H, /12 = L
J220 Motronic engine control module B6
J623 Engine control module B7
J624 Engine control module 2 B7 4.2 FSI (BNS, RS4) only, see other buses
J217 Transmission control module B6, B7 Automatic / multitronic only
J104 ABS/ESP control module B6, B7
J234 Airbag control module B6, B7
J527 Steering column electronics B6, B7 Also on convenience CAN
J236 Servotronic control module B6 Diagram 327
J431 Headlight range control module B7 Bi-xenon with cornering light (diagram 64). On the B6 it uses the L-line, not CAN
Code Module Gen. Notes
J285 Instrument cluster (gateway) B6, B7 Blue T32/17 = H, /18 = L
J527 Steering column electronics B6, B7
J519 Vehicle electrical system control module B6, B7
J393 Comfort system central control module B6, B7
J386, J387 Front door control modules B6, B7 Built into the window motors
J388, J389 Rear door control modules B6, B7 Optional (SSP 254)
E87 A/C control head B6 SSP 254: on the convenience CAN, diagnosed via K-wire
J255 Climatronic control module B6, B7
J136 Memory seat control module B6, B7
J345 Towing recognition control module B6, B7
J446 Parking aid control module B6, B7
J364 Auxiliary heater control module B6, B7
J502 Tyre pressure monitoring control module B7 Also in the SSP 254 B6 topology, but the manual only has the B7 TPMS diagram (69)
J503 Radio/navigation display control module B7 Also on infotainment CAN
J810 Power seat control module B7 Diagram 116
Engine control module B7 The MY2006 comfort sheet (p. 715) shows “J…” (engine control module, “see current engine diagram”) on A146/A147
Code Module Gen. Notes
J285 Instrument cluster (gateway) B6, B7 Blue T32/20 = H, /19 = L
R Radio B6, B7
J401 Navigation system with CD drive B6, B7
J402 Operating electronics, navigation B6, B7
J503 Radio/navigation display control module B7
J526 Telephone/telematics control module B6, B7 CAN pins drawn on B6 sheets
R36 Telephone transceiver B6, B7
J412 Operating electronics, telephone B6
J507 Speech input control module B6
R94 Navigation interface B6
R99 Chip card reader (Audi Logbook) B6
R146 Satellite radio B6, B7 North America

SSP 269 gives the VW Group rule: CAN wires are orange. CAN-High has a second colour that identifies the bus: black for drivetrain, green for convenience, violet (lilac) for infotainment. CAN-Low is always orange/brown. The A4 manual follows this rule without exception on the three main buses:

Bus SSP 269 rule A4 manual (High / Low) Gauge in manual
Drivetrain orange/black, orange/brown or/sw / or/br 0.35 mm² (0.22 at some modules)
Convenience orange/green, orange/brown or/gn / or/br 0.35 mm²
Infotainment orange/violet, orange/brown or/li / or/br 0.35 mm²

The three CAN-Low wires all have the same colour, so check the splice code or the High wire it is twisted with before you cut into a harness. See Wire colours and terminals for the German colour abbreviations.

Some short point-to-point buses do not use the orange colour code:

  • Navigation bus (B6): J402, the navigation/TV tuner J415 and the navigation interface R94 share their own pair through splices A148 (High, gr/ro) and A149 (Low, gr/ws). See manual p. 266. SSP 254’s topology shows the same short J402–R94 link.
  • Cornering-light bus (B7): the headlight range control module J431 sits on the drivetrain CAN and also runs a separate pair to the cornering light motors V318 and V319. This pair goes through splices B229 (ws/ro) and B230 (gn/ro) and is not connected to A121/A122 (p. 711).
  • Twin engine control modules (B7 4.2 FSI, BNS): J623 and J624 are both on the drivetrain CAN. They also have a direct or/sw + or/br pair between pins 90 and 89 (p. 615).
  • LIN bus (B7): one single-wire link from J519 to the rain/light sensor G397. See LIN, MOST and Bluetooth.
  • No MOST bus. There is no optical bus anywhere in the A4 manual.

The A4 manual does not draw any terminating resistors: they are inside the modules. The VW Group values from SSP 269, not confirmed for the A4, are in Load resistances; the readings to expect when measuring are under Fault finding below.

The owner’s guess is about right. The A4 uses the standard 16-pin OBD connector, but for Audi’s own workshop diagnosis it uses K-line plus a second K-line (the “L-line”), not a separate diagnosis CAN. SSP 254 says that for communication between the modules and the tester “two diagnosis wires (K and L) are available”. The manual draws exactly that:

  • The K-line (A76, gn/ro) connects the cluster/gateway and the engine, gearbox, ABS, airbag, comfort central, telephone, A/C and Servotronic modules.
  • The L-line (A159, gn/bl) connects a second group: radio, navigation units, parking aid, memory seat, TPMS, J503, J810 and (B6) headlight range control.

The separate diagnosis CAN of SSP 286, a 500 kbit/s pair to a J533 gateway, belongs to the A8 ’03 and later cars. It does not exist in the A4 manual (see LIN, MOST and Bluetooth).

OBD-II port

OBD-II port face, pins 1–16. Grounds 4/5 are in green and battery + (16) in red. From the owner’s pinout sheet.

Pin Function B6 (diagram 312, p. 950) B7 from 11.2004 (diagram 61, p. 437)
1 Terminal 15 (ignition) sw/bl from fuse S231 (15 A) same
4 Chassis ground br to ground 135 same
5 Signal ground br to ground 135 same
6 CAN-High not wired or/sw to A121 (drivetrain CAN-H)
7 K-line gn/ro to A76 to J285 T32a/23 same
14 CAN-Low not wired or/br to A122 (drivetrain CAN-L)
15 L-line gn/bl to A159 same
16 Terminal 30 (battery +12 V) ro/sw from fuse S12 (10 A) same

The owner’s sheet calls pin 4 chassis ground and pin 5 signal ground (the OBD standard names). In the A4 manual both run to the same ground point 135. The B7 also has an engine-harness K-line splice D166 for the engine and gearbox modules.

The following comes from SSP 269 (VW Group procedure), with A4 measuring points from the wiring manual. For the full procedure and the worked examples, see Drivetrain and convenience CAN.

  1. Start with the fault memory. Read the cluster/gateway’s fault memory and measured value blocks. In the SSPs the blocks from 125 cover the drivetrain and the blocks from 130 the convenience bus; on another car the numbering may differ, so follow the on-screen text. A “1” means the module is talking and “0” means it is not. Convenience modules can also show “single wire”. Typical messages are “Module — no signal/communication” (one module or one branch) and “Drivetrain data bus defective” (the whole bus, often a short).

  2. One module missing: unplug it and check for bent, pushed-back or corroded pins. Then follow its stub to the splice (A121/A122, A146/A147 or A178/A179) or to the next working module.

  3. Drivetrain bus, resistance check: switch the ignition off first. On a B7 measure between DLC pins 6 and 14. On a B6, where those pins are empty, measure at the cluster’s green connector, T32a pin 13 (or/sw) against pin 12 (or/br), or at any other drivetrain module. Expected values, using SSP 269’s group figures:

    Reading H–L Likely meaning
    about 53–66 Ω bus and load resistors OK
    about 250 Ω or more open circuit, often in the branch to the engine control module (the 66 Ω resistor is missing)
    about 30 Ω or less short between High and Low
    High or Low to earth about 300 Ω or less short or partial short to earth
  4. Drivetrain bus, voltages: a multimeter only shows an average; to see real faults you need a scope. The levels and scope settings are in Signal levels and the worked examples.

  5. Convenience/infotainment bus: disconnect the battery before any ohmmeter work (these buses stay powered from terminal 30), and use the bus’s single-wire mode to narrow the fault down: see the convenience procedure. On the A4 the door modules J386–J389 and J393 are all on A146/A147. The door modules’ CAN wires pass through the door connectors at the A- and B-pillars, T20 to T20c (manual p. 714); when hunting a short, SSP 269 suggests splitting the harness at these door connectors first.

  6. Swapped wires are mostly caused by repairs or retrofits. Check the colours: High is or/sw, or/gn or or/li; Low is always or/br.

In the wiring data

Everything drawn in this system’s diagrams of the factory manual, generated when the site is built. A part drawn in several systems is listed on each of them. Locations say how they were worked out; the component pages have every pin.

Control modules

CodeNameLocationAlso on
J104ABS Control Module (w/EDL)In engine compartment, on hydraulic unit, front leftmanual textInstrument cluster, Basic equipment (J519, J527), Headlights and auto-dimming mirror, Convenience system, Body options, Sound system, Navigation and telephone, ABS and ESP, Steering wheel and Servotronic
J136Memory Seat Control ModuleUnder the driver's seat, on the seat frameoutside referenceInstrument cluster, Convenience system, Seats and power mirrors
J217Transmission Control Module (TCM)In electronics box, plenum chambermanual textInstrument cluster, 1.8 T engine (AMB), 3.0 V6 engine (AVK, BGN), 4.2 V8 engine, S4 (BHF, BBK), 2.0 TFSI engine (BGB, BPG), 3.2 FSI V6 engine (AUK, BKH), Automatic gearbox (tiptronic), multitronic gearbox
J234Airbag Control ModuleBelow centre console, in front of handbrake levermanual textInstrument cluster, Basic equipment (J519, J527), Convenience system, Navigation and telephone, Airbags and belt tensioners, Steering wheel and Servotronic, 1.8 T engine (AMB), 3.0 V6 engine (AVK, BGN), 4.2 V8 engine, S4 (BHF, BBK), 4.2 FSI V8 engine, RS4 (BNS)
J255Climatronic Control ModuleIntegrated with Interior Temperature Sensor Fan -V42- and Instrument Panel Interiormanual textInstrument cluster, Basic equipment (J519, J527), Climate control, Seats and power mirrors
J285Control module with indicator unit in instrument panel insertBehind display unitmanual textInstrument cluster, Basic equipment (J519, J527), Headlights and auto-dimming mirror, Convenience system, Climate control, Seats and power mirrors, Body options, Sound system, Navigation and telephone, Airbags and belt tensioners, ABS and ESP, Steering wheel and Servotronic, 1.8 T engine (AMB), 3.0 V6 engine (AVK, BGN), 4.2 V8 engine, S4 (BHF, BBK), 2.0 TFSI engine (BGB, BPG), 3.2 FSI V6 engine (AUK, BKH), 4.2 FSI V8 engine, RS4 (BNS), Automatic gearbox (tiptronic), multitronic gearbox
J345Control Module for towing sensorWired into the instrument panel wiring harnessinferred from wiringInstrument cluster
J364Control module for auxiliary heaterWired into the instrument panel wiring harnessinferred from wiringInstrument cluster
J386Door control module, driver sideIntegrated in electric window motormanual textHeadlights and auto-dimming mirror, Convenience system, Seats and power mirrors, Body options, Navigation and telephone
J387Door control module, passenger sideIntegrated in electric window motormanual textHeadlights and auto-dimming mirror, Convenience system, Seats and power mirrors
J388Door control module, rear, leftIntegrated in electric window motormanual textConvenience system
J389Door control module, rear, rightIntegrated in electric window motormanual textConvenience system
J393Central control module for comfort systemAt sill panel, front leftmanual textInstrument cluster, Basic equipment (J519, J527), Convenience system, Body options, Sound system, Navigation and telephone, Airbags and belt tensioners, ABS and ESP, 2.0 TFSI engine (BGB, BPG), 3.2 FSI V6 engine (AUK, BKH), 4.2 FSI V8 engine, RS4 (BNS)
J401Navigation System with CD Drive Control ModuleIn centre consolemanual textInstrument cluster, Convenience system, Body options, Sound system, Navigation and telephone
J402Control module for operating electronics, navigationIn top center consolemanual textInstrument cluster, Convenience system, Body options, Sound system, Navigation and telephone, ABS and ESP
J412Control module for operating electronics, TelephoneCentre console / armrest, telephone installationinferred from nameInstrument cluster, Navigation and telephone
J415Tuner for navigation/TVIn luggage compartment left, behind side trimmanual textBody options, Sound system, Navigation and telephone
J431Headlight Range Control ModuleBehind glove boxmanual textInstrument cluster, Basic equipment (J519, J527), Headlights and auto-dimming mirror
J446Control module for parking aidOn rear cross panel, luggage compartment, left, behind trim near left rear lightmanual textInstrument cluster, Body options
J503Radio/Navigation Display Control ModuleAt the top of the center consolemanual textInstrument cluster, Sound system, Navigation and telephone
J507Speech Input Control ModuleIn the electronics box under the front passenger's (right front) seatoutside referenceInstrument cluster
J519Vehicle Electrical System Control ModuleBehind driver's storage compartmentmanual textInstrument cluster, Basic equipment (J519, J527), Headlights and auto-dimming mirror, Convenience system, Body options, Navigation and telephone, Automatic gearbox (tiptronic), multitronic gearbox
J526Telephone/Telematic Control ModuleIn Electronics box under the front passenger seatmanual textInstrument cluster, Convenience system, Sound system, Navigation and telephone, Airbags and belt tensioners
J527Steering Column Electronic Systems Control ModuleAt steering columnmanual textInstrument cluster, Basic equipment (J519, J527), Seats and power mirrors, Body options, ABS and ESP, Steering wheel and Servotronic, 1.8 T engine (AMB), 3.0 V6 engine (AVK, BGN), 4.2 V8 engine, S4 (BHF, BBK), 2.0 TFSI engine (BGB, BPG), 3.2 FSI V6 engine (AUK, BKH), 4.2 FSI V8 engine, RS4 (BNS)
J810Front Passenger's Power Seat Control ModuleIn or under the front passenger's seatinferred from nameInstrument cluster, Seats and power mirrors

Other components

Ignition switch (1)

  • D Ignition/Starter Switch

Motor (2)

  • V318 Left Dynamic Cornering Light Motor
  • V319 Right Dynamic Cornering Light Motor

Radio / antenna (5)

  • R Radio
  • R36 Telephone Transceiver
  • R94 Navigation Interface
  • R99 Chip Card Reader
  • R146 Satellite Radio

Switch (1)

  • E87 A/C Control Head

Splices

  • A2 Ignition-switched positive (terminal 15)
  • A32 Battery positive, permanent (terminal 30)
  • A57 Battery positive, permanent (terminal 30)
  • A70 Ignition-switched positive, fused (terminal 15a), fuse 231
  • A76 K-line (diagnosis)
  • A121 Drivetrain CAN High
  • A122 Drivetrain CAN Low
  • A146 Comfort CAN High
  • A147 Comfort CAN Low
  • A148 Navigation CAN High
  • A149 Navigation CAN Low
  • A159 L-line (diagnosis), to diagnostic connection T16 pin 15
  • A178 Infotainment CAN High
  • A179 Infotainment CAN Low
  • B229 CAN High of J431's own bus to the cornering light motors V318 and V319 (not the drivetrain CAN)
  • B230 CAN Low of J431's own bus to the cornering light motors V318 and V319 (not the drivetrain CAN)
  • D159 Drivetrain CAN High
  • D160 Drivetrain CAN Low

Diagrams

  • 30 CAN-Bus wiring (B6 only)
  • 61 Data Link Connector (DLC) (B7 only)
  • 111 Can-Bus wiring (B7 only)
  • 312 Diagnostic connection (B6 only)
  • 331 CAN-Bus wiring (B6 only)

Modify

Understand

Look up

Parts in the wiring data

CodeNameModelsLocation
J285Control module with indicator unit in instrument panel insertB6 and B7Behind display unit
J527Steering Column Electronic Systems Control ModuleB6 and B7At steering column
J519Vehicle Electrical System Control ModuleB6 and B7Behind driver's storage compartment
J393Central control module for comfort systemB6 and B7At sill panel, front left
J220Motronic Engine Control Module (ECM)B6 onlyIn electronics box, plenum chamber
J623Engine Control Module (ECM)B7 onlyUnder the plenum chamber cover
J217Transmission Control Module (TCM)B6 and B7In electronics box, plenum chamber
J104ABS Control Module (w/EDL)B6 and B7In engine compartment, on hydraulic unit, front left
J234Airbag Control ModuleB6 and B7Below centre console, in front of handbrake lever
A121Wire connection (High-bus), in instrument panel wiring harnessB6 and B7Splice inside the instrument panel wiring harness
A122Wire connection (Low-bus), in instrument panel wiring harnessB6 and B7Splice inside the instrument panel wiring harness
D159High-Bus Connection (in engine compartment wiring harness)B6 and B7Splice inside the engine compartment wiring harness
D160Low-Bus Plus Connection (in engine compartment wiring harness)B6 and B7Splice inside the engine compartment wiring harness
A146Comfort System High-bus Connection (in instrument panel wiring harness)B6 and B7Splice inside the instrument panel wiring harness
A147Comfort System Low-bus Connection (in instrument panel wiring harness)B6 and B7Splice inside the instrument panel wiring harness
A178Infotainment High-bus Connection (in instrument panel wiring harness)B6 and B7Splice inside the instrument panel wiring harness
A179Infotainment Low-Bus Connection (in instrument panel wiring harness)B6 and B7Splice inside the instrument panel wiring harness
A76Wire connection (K-diagnosis wire), in instrument panel wiring harnessB6 and B7Splice inside the instrument panel wiring harness
A159Connection (L) (in instrument panel wiring harness)B6 and B7Splice inside the instrument panel wiring harness

Sources