Occupant protection (airbags and belt tensioners)
The B6 airbag system 8.4 E from SSP 254: crash sensors, how deployment is triggered, passenger-airbag deactivation and the crash signal outputs, with where the B7 wiring differs.
System overview
Section titled “System overview”The B6 launched with airbag system 8.4 E, where the E stands for “extended”. It is a further development of the 8.4 system. The airbag control unit J234 sits below the centre console, in front of the handbrake lever.

Figure: SSP 254
According to SSP 254, the saloon at launch had:
- driver and front-passenger airbags;
- front side airbags, with rear side airbags as an option;
- SIDEGUARD head airbags;
- front three-point belts with ball-type belt tensioners and belt-force limiters;
- three-point belts in the outer rear seats, a centre lap belt (with the fixed rear bench), and Isofix preparation in the rear;
- six external acceleration sensors (“crash sensors”), mounted as close to the outer structure as possible so that an impact is detected sooner. They send digitised acceleration values to J234, which evaluates them.
| SSP 254 code | Component | B6 diagram 307 in the 12.2005 manual |
|---|---|---|
| G283 / G284 | Front airbag crash sensor, driver / passenger | same codes (manual p. 921) |
| G179 / G180 | Side airbag crash sensor, driver / passenger (B-pillar) | same codes (manual p. 919) |
| G256 / G257 | Rear side airbag crash sensor, driver / passenger | same codes (manual p. 919) |
| N95 / N131 | Front airbag igniter, driver / passenger | same codes, plus coil spring F138 (manual p. 915) |
| N153 / N154 | Front belt tensioner igniter, driver / passenger | same codes (manual p. 915). The database has them only from the B7 diagrams: N153, N154 |
| N199 / N200 | Side airbag igniter, driver / passenger | same codes (manual p. 918) |
| N201 / N202 | Rear side airbag igniter | same codes (manual p. 919) |
| N277 / N278 | SIDEGUARD head airbag igniter | N251 / N252 “igniter for head airbag” (manual p. 916) |
| E224 | Key switch to deactivate the passenger airbag | same code |
| K75 | Airbag warning lamp (in cluster J285) | same code |
| K145 | “Airbag off” warning lamp, passenger side | same code |
The manual’s diagram 307 draws every igniter. The wiring database, however, did not pick up N95, N131, F138, N201, N202, N251 or N252 (or N153/N154 for the B6), so those codes are not linked. Use the sheet links instead. Note also that SSP 254 and the 12.2005 manual use different codes for the head-airbag igniters.
Sensor locations
Section titled “Sensor locations”- Front sensors G283/G284: SSP 254 says they are integrated into the front bumper area. Its photo shows them at the front end, next to the headlight. In the manual their wiring runs through the A-pillar connector stations (T17a left, T17c right). See the manual’s airbag component locations and the 3D view of G283.
- Side sensors G179/G180: at the B-pillars. Their wiring runs through the door/A-pillar connectors T20 and T20a.
- Rear sensors G256/G257: the manual describes them as “at the rear wheel housing liner”. SSP 254 calls them the C-pillar sensors.
How triggering works
Section titled “How triggering works”Front impact. G283 and G284 work together with the crash sensor and the safing sensor inside J234. If a front sensor exceeds a signal threshold, J234 lowers its own trigger threshold, so the restraints fire sooner.
Deployment has two stages, depending on the deceleration:
| Threshold | What fires |
|---|---|
| 1 | Belt tensioners only |
| 2 | Belt tensioners and airbag(s) |
SSP 254’s crash timeline shows the sequence: impact, then belt tensioners, front airbags, airbags fully inflated, belt-force limiter, steering-column damping, and finally the vehicle rebound. The chart covers roughly the first 150 ms.
Side impact. Two independent signals must agree before anything fires:
- the opposing pair of external sensors (left and right B-pillar, and/or left and right C-pillar), and
- the internal crash sensors in J234.
The sensors are designed so they cannot be fitted the wrong way round.
After a crash
Section titled “After a crash”- K75 stays lit permanently after a recorded impact.
- The fault memory shows “CRASH DATA STORED” and lists which components fired.
- Once the first crash record has been stored, J234 can no longer be re-coded. The workshop manual lists which sensors and parts must be replaced.
Passenger-airbag deactivation
Section titled “Passenger-airbag deactivation”- The passenger airbag can only be switched off with the key switch E224. K145 shows that it is off. On the A4, switching off also deactivates the passenger side airbag.
- It cannot be switched off with a diagnostic tester.
- To add the function to a car without it, fit the key switch and the “airbag off” lamp, then re-code J234.
Belts and head restraints
Section titled “Belts and head restraints”- The front belt buckle and the belt anchorage are fixed to the seat frame. Combined with the height adjuster, the belt sits correctly in every seat position.
- The front head restraints have an integrated locking mechanism.
- The belt switches E24 and E25 are wired to J234. The left one is also wired to the cluster (B6 diagram: J285 T32a/30, see Instrument cluster).
Crash signal outputs
Section titled “Crash signal outputs”SSP 254 describes two separate crash outputs from J234:
- Hard-wired crash line, which:
- triggers an emergency call through the telephone/telematics unit J526 (option);
- makes the convenience control unit J393 unlock the car, switch on the interior lights (if their switch is on “door contact”) and switch on the hazard lights;
- makes J393 switch off the optional auxiliary heater (J162 in SSP 254) with a CAN message.
- CAN message, which makes the engine control unit (J220) cut the fuel supply. SSP 254 says this message goes over the convenience bus.
What the wiring database shows:
- B6 (307): the crash line is J234 pin 69 (li/bl). In the comfort and engine diagrams it runs to J393 pin 8, to J526, and also to the engine control module J220. So on the cars covered by the 12.2005 manual, the engine gets a wired crash signal as well.
- B6 CAN connection: J234 sits on the drive CAN (pins 2/3), not the convenience CAN. A message to J220 would not need to pass through the gateway.
- B6 steering column: J234 pins 33/34 run through the 4-pin connector T4e on the steering column module J527, then through the coil spring F138 to the driver’s airbag igniter N95 (manual p. 915).
B7 differences in the wiring data
Section titled “B7 differences in the wiring data”The B7 airbag diagrams (54 from 11/2004, 105 from MY 2006) use a different J234 pin layout from the B6 diagram 307:
- crash signal on pin 53;
- drive CAN on pins 74/75;
- front sensors on pins 67/68.
The B7 diagrams also add parts that the B6 diagram does not have:
- seat-occupied recognition: control module J706 with G128, G452 and G453;
- in the MY 2006 diagram, the battery interrupt igniter N253.
Both generations’ diagrams show rear belt tensioner igniters N196, N197 and N198, which SSP 254 does not mention. Do not swap an airbag control unit between generations without checking the part number and coding.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J234 | Airbag Control Module | B6 and B7 | Below centre console, in front of handbrake lever |
G283 | Driver's Front Airbag Crash Sensor | B6 and B7 | Wired into the main wiring harness |
G284 | Front Passenger's Front Airbag Crash Sensor | B6 and B7 | Wired into the main wiring harness |
G179 | Driver's Side Airbag Crash Sensor | B6 and B7 | Its wires run through T20 (Door A-pillar, left) |
G180 | Front Passenger's Side Airbag Crash Sensor | B6 and B7 | Its wires run through T20a (Door A-pillar, right) |
G256 | Rear Side Airbag Crash Sensor (on driver's side) | B6 and B7 | At the rear wheel housing liner |
G257 | Rear Side Airbag Crash Sensor (on front passenger's side) | B6 and B7 | At the rear wheel housing liner |
N199 | Igniter for side airbag, driver's side | B6 and B7 | Right/left side of the front driver/passenger seat |
N200 | Front Passenger's Side Airbag Igniter | B6 and B7 | Right/left side of the front driver/passenger seat |
N196 | Rear Safety Belt (driver's side) Tensioner Igniter | B6 and B7 | Its connector T2aa is described as: passenger compartment rear left |
N197 | Rear Safety Belt (front passenger's side) Tensioner Igniter | B6 and B7 | Its connector T2ab is described as: passenger compartment rear right |
N198 | Center Rear Safety Belt Tensioner Igniter | B6 and B7 | Its connector T2ac is described as: passenger compartment rear center |
E224 | Front Passenger's Airbag -Off- Key Switch | B6 and B7 | Wired into the airbag wiring harness |
K75 | Airbag Malfunction Indicator Lamp (MIL) | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
K145 | Warning light for airbag off, passenger side | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
E24 | Left Seat Belt Switch | B6 and B7 | Wired into the airbag wiring harness |
E25 | Right Safety Belt Switch | B6 and B7 | Its wires run through T8c (Connector station - RF seat wiring) |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J526 | Telephone/Telematic Control Module | B6 and B7 | In Electronics box under the front passenger seat |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 12–17 (occupant protection).
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseB6 airbag diagram 307; B7 airbag diagrams 54 and 105.