Installing an aftermarket head unit
Fitting an aftermarket radio: where to get ignition power, why only the front speakers play, and how to keep or bypass the factory amplifier.
What you need
- Tools
- Radio release keys (4 for a 2-DIN unit, 2 for 1-DIN)
- Wiring
- 4 parts in the wiring data, with their locations and pins
A rundown of fitting an aftermarket head unit in an Audi A4 B6. Most of it applies to the B7 as well, although the B7’s radios use a different connector (see Radio and amplifier pinouts).
The three questions that come up every time:
- Where do I get ignition power from? There is no ignition wire at the radio.
- Why do I only have sound from my front speakers? The rear speakers hang on the factory amplifier.
- How do I keep the factory amplifier? It needs line-level inputs and a “radio on” signal.
Background
Section titled “Background”Bose or standard
Section titled “Bose or standard”There are two factory sound systems. With Bose, the Bose amplifier in the luggage compartment drives every speaker; with the standard system, the head unit drives the front speakers and an amplifier in the same place drives the rear ones. Details in OEM sound system.
No ignition wire
Section titled “No ignition wire”The B6 radio has no dedicated ignition (terminal 15) wire. It learns the ignition state over the infotainment CAN bus (connector C, pins 7 and 12, or/li and or/br, which run to the instrument cluster J285: see CAN bus). An aftermarket radio cannot read that, so your options are:
- run the radio’s ignition input from permanent power (simplest, see below);
- use an adapter that reads the ignition state from CAN;
- fetch an ignition-switched supply from elsewhere, e.g. with a fuse tap on a fuse that is live only with the ignition on (check the fuse panel: the Terminal column shows which fuses are on terminal 15).
The connectors behind the radio
Section titled “The connectors behind the radio”There are three, sometimes four, connectors behind the head unit. On some units (like the B7’s RNS-E) they share one housing.

| Connector | Pins | Colour | Carries |
|---|---|---|---|
| A | 8 | black | Power: terminal 30, ground, Bose coding |
| B | 8 | brown | Front speakers (standard system); unused for speakers with Bose |
| C | 20 | black | Amplifier line outputs, CAN, CD changer |
| D | 10 | red | Telephone and navigation audio (only if fitted at the factory) |
These belong to the car’s harness, not the radio, so they are the same whichever factory B6 head unit was fitted. Pin by pin, checked against the factory manual: Radio and amplifier pinouts.
Hardware
Section titled “Hardware”What you need depends on the factory system and what you want to keep:
| Item | Why |
|---|---|
Radio release keys (4 for a 2-DIN unit, 2 for 1-DIN) |
To pull the factory radio. |
Universal ISO adapter |
Plugs into connectors A and B so you don’t cut the car’s harness. You may need to move some pins around. |
Mini ISO (20-pin) adapter |
Plugs into connector C, again without cutting anything. |
Line-out adapter |
Feeds the factory amplifier (Bose or standard) from the new radio’s RCA outputs. |
Multifunction (CAN) adapter |
All in one: replaces the adapters above, provides the ignition signal from CAN, and makes the steering-wheel buttons work. Varies with factory equipment (Bose or not). |
You can do the CAN translation yourself (reading ignition and steering-wheel buttons off the infotainment bus), but only if you know what you are doing and want that control. Otherwise the multifunction adapter is the plug-and-play route.
Installation
Section titled “Installation”1. Decide what to keep
Section titled “1. Decide what to keep”Settle these first, preferably before buying anything:
- Keep the factory amplifier? Then you need the mini ISO adapter with line-out plugs. Feed the amplifier’s line inputs (connector C pins 1 and 2, plus 4 and 5 with Bose) and its switched positive (C6) from the new radio. On the standard system, the amplifier only switches on when C6 is live.
- Run every speaker from the amplifier? Bose already does. On the standard system you would need to rewire the front speakers to the luggage compartment instead of the centre console. Not covered here.
- Run every speaker from the head unit?
- Standard system: the front speakers are already at the radio, so you only need to bring the rear door speakers forward. If you don’t keep the amplifier, the easy way is to send the rear speaker signals back through the amplifier’s line-signal wires, which already run from the radio to the luggage compartment. See Running the rear speakers from the head unit below.
- Bose: all speakers end at the amplifier. The harness has only four signal wires from the front (two line channels each for front and rear, plus ground), and you need eight (two per speaker). You will have to run new wire.
2. Power
Section titled “2. Power”- With a multifunction adapter, check its manual. It is usually plug and play.
- With ISO adapters: the head-unit side of the ISO plug is fairly standard, but check your radio’s diagram. Then rearrange the car-side pins to match connector A: terminal 30 (permanent) on pin 7, ground on pin 8.
- Without an ignition signal: join the radio’s yellow (permanent) and red (ignition) wires and put both on terminal 30. The radio then works with the ignition off, and you have to switch it off yourself (it will drain the battery if forgotten).
- With an ignition signal: put the red wire on an ignition-switched source, either a fuse tap on a terminal-15 fuse or the ignition output of a CAN adapter.
3. Sound
Section titled “3. Sound”This depends on the decisions in step 1. Use the pinouts to map the new radio’s outputs:
- front speakers on connector B (standard system);
- amplifier line inputs and switched positive on connector C;
- with Bose, everything goes through connector C to the amplifier.
Running the rear speakers from the head unit
Section titled “Running the rear speakers from the head unit”The owner’s own solution, on a standard-system car with the factory amplifier no longer used:
- At the front, a mini ISO adapter was modified and joined to the universal ISO adapter’s rear speaker wires. The rear speaker outputs of the new radio now go into the amplifier line-signal wires on connector C (pins 1, 2 and 3).
- At the back, rather than cutting the harness, the owner made an adapter from the plug of an old amplifier of the same type: the plug was cut off the circuit board, and on it the speaker pins were joined to the line-signal pins. The signal arriving from the front now goes straight to the rear door speakers.


With the standard amplifier’s pinout, that means:
| Line signal in (from radio) | joined to | Speaker out |
|---|---|---|
| pin 3 (left rear) | → | pin 17 (left rear +) |
| pin 2 (signal ground) | → | pins 18 and 21 (left rear −, right rear −)* |
| pin 1 (right rear) | → | pin 20 (right rear +) |
* On a standard-system car there are only three line wires (left, right and a common). Both rear speakers’ − leads then share the common. That is only safe if the radio’s rear − outputs may be joined. Most aftermarket head units have bridged (BTL) outputs, where − is not ground, and joining two − outputs together or to ground can damage the radio. If yours are bridged, run separate − wires. The original write-up does not say which pins were used; the table is what the pinout implies.
Personal notes
Section titled “Personal notes”- Multifunction adapter: convenient and makes for a straightforward install, but expensive, especially without steering-wheel controls. If you want the ignition signal and don’t want to fiddle, it is the way to go.
- No ignition signal: the owner skipped it. The upside is that you can play music with the ignition off. The downside is the battery drain if you forget to switch it off.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
R | Radio | B6 and B7 | Top of the center console |
R12 | Amplifier | B6 and B7 | In luggage compartment right, behind side trim |
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
S239 | Fuse in fuse holder | B6 and B7 | Fuse panel at the left end of the instrument panel, fuse No. 39 |
Sources
- Installing Aftermarket Head Unit in A4 B6 (owner's write-up)Written for a B6 Avant with the standard (non-Bose) system and a Concert II head unit.
- A4 B6 – Pinouts / Wire Diagrams (owner's sheet)
Radio release keys (4 for a 2-DIN unit, 2 for 1-DIN)
Universal ISO adapter
Mini ISO (20-pin) adapter
Line-out adapter
Multifunction (CAN) adapter