Electric rear windows
Converting a B6 with wind-up rear windows to electric. A lot of work: the harness through both B-pillars and inside each rear door has to change.
What you need
- Difficulty
- Advanced
- Tools
- VCDS or similar (comfort module coding)
- Coding
- Yes: see the coding steps in the article
- Parts
- 5 part numbers in this article, listed below the text
- Wiring
- 14 parts in the wiring data, with their locations and pins
US cars nearly always have electric rear windows. European cars can have manual (wind-up) rear windows, and this is how to convert them.
Cars built before about 2003 may differ: production changes were made around then.
Part numbers starting 8E1 are for left-hand drive; for right-hand drive they read 8E2.
| Part | Number | Notes |
|---|---|---|
| Rear door control module, left | 8E0 959 801 E | Built into the window motor (J388 with V26) |
| Rear door control module, right | 8E0 959 802 E | J389 with V27 |
| Driver’s window switch block | 8Z0 959 851 B / F | Adds the rear window switches E53/E55 and the child safety switch E39 |
| Rear door window switch | 8Z0 959 855 (C), ×2 | E52 and E54 |
| Comfort control module | 8E0 959 433 AJ | J393. Not sure which versions can be coded for electric rear windows: check that yours can. |
| Rear door panels with the switch cut-out | — | Easiest second-hand. |
| Interior B-pillar harness | — | No separate number: part of the main interior harness. |
If your car is pre-2003 and you change the comfort module, you will probably need new keys: check the remote frequency of your current keys and module against the new module.
How it is wired at the factory
Section titled “How it is wired at the factory”In the comfort diagrams, each rear window motor has its own door control module built in (J388, J389), on the comfort CAN bus with the front door modules and the comfort module J393. From the manual:
- The rear door’s own switch (E52/E54) is wired to that door’s motor/module on its 16-pin connector (
T16d/4,sw/gnon the left), together with the switch illumination (terminal 58s) and ground. - The driver’s switches E53/E55 and the child safety switch E39 are wired to the driver’s window motor with its door module (V14 / J386, connector
T32c). The request reaches the rear door over the comfort CAN bus. - Through the B-pillar each rear motor gets, on its 10-pin connector
T10g: ground (br, ground point 77 on the lower B-pillar), permanent positive through fuse S280 “Power window fuse 2” (ro/bl; S37 feeds the front motors), a fused supply from S223, and the comfort CAN pair (or/gn,or/br).
So a car with manual rear windows lacks, per rear door: the module/motor, the switch, the power feed and the CAN pair through the B-pillar. That is why the harness through the B-pillar has to change. Open the J388 page for the exact pins, wire colours and sheets.
Procedure (outline)
Section titled “Procedure (outline)”Not written up in detail yet. The gist:
- Remove the rear door panels.
- Replace the wiring harness inside each door with one from a car that has electric rear windows, and fit the module/motor and the regulator.
- Fit door panels with the window switch.
- Run new wires and change the pin layout of the B-pillar harness on both sides (power, ground and comfort CAN to the door). The owner has no pinout of the B-pillar connector yet; use the connector stations and the J388/J389 pages to work it out.
- Code the comfort module for electric rear windows (VCDS or similar).
Shopping list
Every part number in this article. Ticks are kept in this browser for this article only. Check each number against your chassis number before ordering.
8E0 959 801 ERear door control module, leftNot in the loaded part of the catalogue.8E0 959 802 ERear door control module, rightNot in the loaded part of the catalogue.8Z0 959 851 BDriver's window switch blockNot in the loaded part of the catalogue.- Not in the loaded part of the catalogue.
8E0 959 433 AJComfort control moduleNot in the loaded part of the catalogue.
The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J388 | Door control module, rear, left | B6 and B7 | Integrated in electric window motor |
J389 | Door control module, rear, right | B6 and B7 | Integrated in electric window motor |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J386 | Door control module, driver side | B6 and B7 | Integrated in electric window motor |
V14 | Left Window Motor | B6 and B7 | In the driver's (left front) door |
V26 | Motor for window regulator, rear, left | B6 and B7 | — |
V27 | Motor for window regulator, rear, right | B6 and B7 | — |
E52 | Left Rear Window Switch, (In LR Door) | B6 and B7 | In the left rear door |
E54 | Right Rear Window Switch, (In RR Door) | B6 and B7 | In the right rear door |
E53 | Switch for window regulator rear left, driver | B6 and B7 | Driver's door trim, window switch panel |
E55 | Switch for window regulator rear right, driver | B6 and B7 | Driver's door trim, window switch panel |
E39 | Safety switch for window regulator rear | B6 and B7 | Driver's door trim, window switch panel |
S280 | Power Window Fuse 2 | B6 and B7 | Relay carrier (9-position) with vehicle voltage control module, through 2005 MY, position D (brown socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
S37 | Power Window Fuse | B6 and B7 | Relay carrier (9-position) with vehicle voltage control module, through 2005 MY, position F (black socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
Sources
- A4 B6 – Retrofit Guides (owner's notes)Done on a 2004 B6 Avant. Part numbers from the owner's research.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseComfort system diagrams 318, 6, 35 (B6) and 67, 110 (B7).