LIN, MOST and Bluetooth (SSP 286)
SSP 286's LIN, MOST, Bluetooth and diagnosis CAN, written for the A8 '03, with what the A4 wiring manual actually has of each.
Why new buses?
Section titled “Why new buses?”The first A8 (1994) had at most 15 control modules. The A8 ’03 has about five times as many. CAN suits most control data, but it is too slow for audio and video and too expensive for simple sensors and actuators. SSP 286 therefore adds three systems alongside CAN: LIN for cheap local sub-networks, MOST for fast optical infotainment data, and Bluetooth for wireless devices. It also adds a dedicated diagnosis CAN.
LIN: the single-wire bus
Section titled “LIN: the single-wire bus”LIN means Local Interconnect Network: a small sub-system of modules close together, for example in the roof or the air-conditioning system.
| Property | Value |
|---|---|
| Wiring | One wire, 0.35 mm², no screen. Base colour violet plus a code colour |
| Speed | 1–20 kbit/s (set in software), at most one fifth of the convenience CAN |
| Nodes | One LIN master + up to 16 LIN slaves |
| Recessive level | about battery voltage |
| Dominant level | pulled to earth by the sending transceiver |
| Receive tolerance | wider than the send tolerance, for noise margin (the SSP’s diagram: send ≥ 80 % / ≤ 20 % of battery voltage, receive ≥ 60 % / ≤ 40 %) |
- Master: the master is the only LIN node connected to CAN. It translates between the two and sets the timetable for which message goes out when. It also handles diagnosis for its slaves. Faults show up under the master’s diagnostic address.
- Slaves: small modules, or “intelligent” sensors and actuators (blower, tilt sensor, alarm horn …). A slave only speaks when the master asks.
- Message: the master always sends a header. This is a sync break of at least 13 dominant bits, a sync delimiter, a sync field (alternating 0101…) so the slaves can match the master’s clock, and an 8-bit identifier (6 bits ID/length + 2 check bits). After the header comes the response of 0–8 data fields of 10 bits each, sent either by the master (a command) or by a slave (requested data). The master sends headers for a fully equipped car. Headers for options that are not fitted simply get no answer.
- Security: a slave cannot start a conversation and the master watches all traffic, so LIN nodes can sit outside the car (the SSP’s example is a garage-door-opener module in the bumper). Tapping the wire does not let you, for example, unlock the doors.
- Typical faults: “no signal/communication” (open or short circuit, slave supply fault, wrong slave/master variant, faulty slave) and “implausible signal” (interference, moisture or dirt in a connector, software or variant mismatch).
On the A4: the B7 rain/light sensor wire is li/ge, so it follows the violet-plus-code-colour rule. On this link J519 would be the master. The manual names the wire “LIN-Bus” but does not say which unit is master; the master role here is inferred from SSP 286, not stated.
MOST: the optical bus (A8 ’03, not on the A4)
Section titled “MOST: the optical bus (A8 ’03, not on the A4)”Media Oriented Systems Transport carries audio, video, navigation and telephone data as modulated light.
- Speed: 21.2 Mbit/s, compared with at most 1 Mbit/s for CAN. Digital TV with stereo sound alone needs about 6 Mbit/s.
- Ring topology: each module passes data in one direction to the next. Messages are addressed to a specific receiver instead of broadcast.
- Module parts: optical connector, an LED and a photodiode (the fibre optical transmitter, red light at 650 nm), a MOST transceiver, the standard microcontroller, and an electrical connector for power and ring diagnosis.
- Fibre: polymer (PMMA) core about 1 mm with cladding, 2.3 mm overall. Minimum bending radius 25 mm; kinked below about 5 mm, the fibre must be replaced. Never solder, glue, heat-bond or twist fibres together. Keep the end faces clean and cut square with the special tool.
- Attenuation: measured in dB and added up along the path. 3 dB = half the light. Causes include tight bends, damaged cladding, dirty or scratched end faces, misaligned or gapped connectors and badly crimped ferrules.
- Frames: sent at 44.1 kHz (the CD audio rate). Each frame is 64 bytes: preamble, delimiter, a 60-byte data field split between synchronous data (audio/video, 24–60 bytes) and asynchronous data (maps, internet, 0–36 bytes), two check bytes, status and parity. Mono uses 2 channels (bytes), stereo 4, surround 12.
- States: sleep, standby and power on. A system manager (on the A8 the front information display module J523) and a diagnosis manager (on the A8 the gateway J533) run the ring.
- Ring-break diagnosis: a separate electrical diagnosis wire triggers every module to report whether it is electrically OK and whether light is arriving from its neighbour. A second test at half light power (−3 dB) finds fibres with too much attenuation.
Bluetooth
Section titled “Bluetooth”- 2.40–2.48 GHz, 79 channels of 1 MHz, frequency hopping 1600 times per second.
- Up to 1 Mbit/s and up to three voice channels. Range about 10 m.
- Devices are paired once with a PIN. A piconet has one master and up to 7 more active devices.
- 128-bit encryption and authentication, with a new key for each connection.
- On the A8 ’03: links the cordless handset to the telephone/telematics module J526, which is the Bluetooth master. Diagnosis goes through J526’s address word. The link is monitored by checking the Bluetooth aerial. Bluetooth can be switched off by adaption, for example for air transport or in countries where the frequencies are not allowed.
On the A4: the manual only shows the Bluetooth antenna R152 on the telephone transceiver R36 (B6 p. 284, B7 p. 776). The manual says nothing about which unit is the Bluetooth master or how it is diagnosed.
Diagnosis CAN (A8 ’03, not on the A4)
Section titled “Diagnosis CAN (A8 ’03, not on the A4)”On the A8 ’03 the tester talks to the gateway J533 over its own CAN instead of the K- and L-lines. The exception is emissions-related modules, which keep the K-line.
- Twisted pair, 0.35 mm². CAN-High orange/violet, CAN-Low orange/brown. 500 kbit/s.
- Allows group addressing (read many fault memories at once) and selective actuator tests.
- Needs VAS 5051 base software 3.0 and the new diagnosis leads VAS 5051/5A or /6A. These also work on K-/L-line cars.
- A module cannot be woken up over the diagnosis CAN. With ignition off, diagnosis works unless the car is in sleep mode, but write functions such as coding are not possible.
SSP 286’s diagnostic connector pin list:
| Pin | A8 ’03 (SSP 286) |
|---|---|
| 1 | Terminal 15 |
| 4, 5 | Earth |
| 6 | Diagnosis CAN High |
| 7 | K-wire |
| 14 | Diagnosis CAN Low |
| 15 | L-wire |
| 16 | Terminal 30 |
The A4’s own pinout, B6 and B7, is in Diagnostic connector (T16) pinout.
Related
Section titled “Related”Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J519 | Vehicle Electrical System Control Module | B6 and B7 | Behind driver's storage compartment |
G397 | Rain/Light Recognition Sensor | B7 only | Its wires run through T17g (Connector station - left A-pillar) |
B528 | Connection (LIN-Bus) (in main wiring harness) | B7 only | Splice inside the main wiring harness |
R152 | Bluetooth Antenna | B6 and B7 | In elctronics box, under front passenger's seat |
R36 | Telephone Transceiver | B6 and B7 | In the electronics box under the right front seat |
Sources
- SSP 286 – New Data Bus Systems: LIN, MOST, Bluetooth — AudiTechnical status 05/02. Written around the Audi A8 '03, not the A4.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database — AudiSearched for LIN, MOST/optical and Bluetooth parts.