RS4-style start button
What you need
- Tools
- 10 mm spanner (battery)
- 8 mm and 13 mm sockets
- Allen key
- Torx drivers
- 12 mm 12-point socket (steering wheel bolt)
- Test lamp or multimeter
- VCDS (to clear the stored faults)
- Parts
- 4 part numbers in this article, listed below the text
- Wiring
- 9 parts in the wiring data, with their locations and pins
The B7 RS4 has a Start Engine button in the centre console. This retrofit fits the same button to an ordinary A4. The key still has to be in the ignition and turned to ON; the button then does what turning the key to START does.
| Part | Number | Price in the guide (2023) |
|---|---|---|
Centre console compartment with cigarette lighter and switch mounting, soul black (5PR) |
8E0 863 284 E | £45.83 / €83 |
| Push button for start system | 8E0 905 217 | £54.99 / €110 |
| Flat contact housing for the button | 8L0 971 883 | €5.98 |
| Repair wire | 000 979 009, ×2 | — |
The console compartment is the tray that holds the cigarette lighter, in a version with a mounting for the button. It replaces the car’s existing lighter tray.
How the factory RS4 wires it
Section titled “How the factory RS4 wires it”The factory manual draws the button as E378 “Start system button” in the RS4 engine diagrams (102, 128, sheets 605 and 802):
| E378 pin | Manual | Function |
|---|---|---|
| 1 | gr/bl 0.35 |
Illumination, terminal 58s (dimmed switch lighting) |
| 3 | br 0.35 |
Ground, terminal 31 |
| 4 | sw 0.35 |
Terminal 15 (ignition on) |
| 6 | bl/br / sw/li 0.35 |
Start signal, to the engine control module J623 and the terminal 50b line |
On the RS4 the button only signals the engine ECU. The ECU then drives the starter through two relays, J53 and J695. The button never carries starter current.
Wiring it into a normal A4
Section titled “Wiring it into a normal A4”The flat contact housing has 8 positions; only 4 are used. They match the factory pins above:
- Pins 1 and 3: illumination. The new console tray comes with three wires: red (12 V for the lighter), grey (illumination) and brown (ground for both). Join the grey wire to pin 1 and the brown to pin 3.
- Pins 4 and 6: the switch. Run a two-core cable (two colours, or mark one end) from pins 4 and 6 along the driver’s footwell, behind the dead pedal and up under the steering column. Leave enough length that you don’t need to extend it.
At the ignition switch:
- Pin 4 goes to the wire that is live with the key in ON (terminal 15).
- Pin 6 goes to the wire that is live only in START (terminal 50).
Pressing the button then connects 15 to 50, just as the key does in START.
Which wires on the A4
Section titled “Which wires on the A4”The guide taps the six-wire lead on the back of the ignition switch (yellow = switched live, red = start). Those are the colours of that lead, not of the car harness. On the harness side, the A4 manual draws the ignition switch D like this:
| D pin | Terminal | Wire | Goes to |
|---|---|---|---|
| 1/50 | 50 | bl 0.35 |
Steering column module J527 T16a/15 (signal only) |
| 5/50b | 50b | ro/sw 2.5 |
Starter B terminal 50, on manual-gearbox cars through the starter lock relay J434 (clutch pedal switch F194) |
| 6/15 | 15 | sw 4.0 |
Terminal 15 fuses |
| 2/75 | 75 | ge/sw 0.5 |
Terminal 75 (off while cranking) |
| 3/30, 7/30 | 30 | ro 2.5 |
Permanent positive |
| 4/P | P | gr/ge 0.35 |
Parking light feed |
| 8/86s | S | ro 0.5 |
Key-in-ignition signal |
Confirm with a test lamp or multimeter before cutting anything: 12 V in ON and START for terminal 15, 12 V only in START for terminal 50/50b. Make the connection on the switch side of the starter lock relay, as the guide does, so the clutch interlock (manual) and the selector-lever interlock (automatic) still work.
Fitting the button (centre console)
Section titled “Fitting the button (centre console)”Condensed from the guide (photos in the original):
- Unclip the trim around the hazard-light button / coin tray.
- Pull the climate control unit down from the top and unclip its four connectors.
- Lift out the gear lever surround (hand underneath, pull up) and unclip the plastic trim from the gaiter.
- Undo the Allen bolt under each grab handle (it stays in the handle), then the 8 mm bolts at the front edge of the grab handles.
- Unclip the lower tray under the climate-control opening; behind it are two more 8 mm bolts. Remove them and the grab handles come out.
- Remove the four Torx screws around the gear lever. (Ashtray versions may have extra bolts.)
- Remove the cap in the driver’s footwell and the 8 mm bolt behind it, and the two caps and 8 mm bolts in the passenger footwell.
- Prise out the cover under the handbrake. Remove the ashtray from the rear (open the lid, pull out) and the tray under it.
- With a front armrest, remove it (13 mm), then the two 8 mm bolts at the rear of the console.
- Lift the console at the back and slide it out over the lowered handbrake. Unplug the cigarette lighter.
- Turn the console over, undo the two Torx screws holding the lighter tray, and swap in the new tray with the button.
Getting to the ignition switch (steering column)
Section titled “Getting to the ignition switch (steering column)”- Disconnect the battery (10 mm), optionally after letting the car stand for 30 minutes. Then press the brake pedal a few times. Leave the key in the ignition, turned to ON, through the job.
- Pull the steering wheel fully out and up, and lock it.
- Turn the wheel 90° left, remove the cover and loosen the Torx screw behind it (it stays captive) until the airbag wobbles; repeat at 90° right. Lift the airbag off and unplug it (orange tab, then the yellow connector; with MFSW also the black one). Put it down face up.
- Remove the centre bolt (12 mm 12-point), mark the wheel and the slip ring, and take the wheel off.
- Unclip the top of the column cover, remove the two Torx screws in the lower cover and the three underneath the column. Remove the column surround.
- Break the seal on the steering column module and remove the small silver Torx screw under the slip ring. Lower the circuit board, then unplug its black and yellow connectors.
- Remove the black cover under the column and unclip the connector at the end of the ignition lock: six wires (yellow, grey, green, blue, purple, red) in a rubber sleeve to a 12-pin connector under the column.
Join the button wires there (see above), reconnect, refit the board.
Testing and finishing
Section titled “Testing and finishing”- Reconnect the battery, key to ON (not in gear), press the button: the engine should start. Check the key still starts it too. With the battery reconnected you will see a steering-wheel warning in the cluster and an ESP message in the DIS; these clear later.
- Disconnect the battery, press the brake a few times, reassemble the column and fit the wheel without the airbag.
- Reconnect, drive a short distance to check the wheel is straight; if not, reposition it by a spline or two.
- Disconnect the battery again, connect and fit the airbag, refit the covers.
- Reconnect. Driving a few metres clears the steering and ESP warnings. If the one-touch windows stop working, run each window fully down and up.
- Clear the stored faults with VCDS (Applications → Gateway installation list: the faults are in red; HVAC, airbag and steering wheel are typical, from the battery being reconnected with them unplugged).
The guide says pressing the button (or turning the key) with the engine running has no effect on its car. That depends on the engine: on engines where the ECU drives the starter through relays (J53/J695 on some B7 engines), the ECU can refuse. Where terminal 50b runs straight to the starter, as on the B6 1.8T, a button wired across 15 and 50b will engage the starter on a running engine. Don’t press it while the engine runs.
Shopping list
Every part number in this article. Ticks are kept in this browser for this article only. Check each number against your chassis number before ordering.
8E0 863 284 ECentre console compartment with cigarette lighter and switch mounting, soul black (5PR)Not in the loaded part of the catalogue.8E0 905 217Push button for start systemNot in the loaded part of the catalogue.8L0 971 883Flat contact housing for the buttonNot in the loaded part of the catalogue.- Not in the loaded part of the catalogue.
The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
E378 | Start System Button | B7 only | Wired into the passenger compartment wiring harness |
D | Ignition/Starter Switch | B6 and B7 | On the steering column, electrical part of the ignition lock |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
J434 | Locking relay for starter (clutch pedal switch) | B6 and B7 | Relay carrier E-Box, engine codes BHF from 2006 MY, position 1.2 — In electronics box (E-box), plenum chamber |
B | Starter | B6 and B7 | On the engine / transmission bell housing |
J623 | Engine Control Module (ECM) | B7 only | Under the plenum chamber cover |
J53 | Starter Relay | B7 only | Relay carrier (9-position) with vehicle voltage control module, from 2006, position 4 (brown socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
J695 | Starter Relay 2 | B7 only | Relay carrier (9-position) with vehicle voltage control module, from 2006, position 3 (green socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
F194 | Clutch Pedal Starter Interlock Switch | B6 and B7 | Clutch pedal switch is located on the pedal bracket with the brake light switch |
Sources
- Audi Retrofit – RS4 Start Button (local copy)Printed 19 May 2023. The page subtitle says "install into 8P A3", but the photos show an A4 B7 interior (RNS-E, B7 climate panel, console grab handles) and the parts are A4 (8E0) numbers.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseE378 in diagrams 102 and 128 (B7 RS4, engine BNS); ignition switch D in the basic equipment and engine diagrams; starter lock relay J434 in diagrams 42 (B6) and 85 (B7).