Vehicle electrical system (J519, J527, MCB)
With the B6 much of the electrical work moved into networked control units. How the vehicle electrical system control unit J519 and the steering column module J527 work, from SSP 254.
With the B6, much of the A4’s electrical work moved into networked control units. SSP 254 shows the main units and where they sit:
| Code | Unit | Where (12.2005 manual) |
|---|---|---|
| J519 | Vehicle electrical system control unit (electronic central electrics) | Behind the driver’s storage compartment |
| J527 | Steering column electronics / switch module | At the steering column |
| J285 | Instrument cluster, with the CAN gateway and immobiliser | Instrument panel |
| J393 | Central convenience control unit | At the sill, front left |
| J234 | Airbag control unit | Below the centre console |
| J104 | ESP control unit (on the hydraulic unit) | Engine bay, front left |
| J386–J389 | Door control units | Integrated in the electric window motors |
| J345 | Trailer recognition control unit | – |
| J431 | Headlight range control | Behind the glove box |
| J293 | Radiator fan control | On the front end, at the radiator fan |
| R99 | Chip-card reader (Audi Logbook) | – |
CAN bus in brief
Section titled “CAN bus in brief”The B6 has three CAN buses (drive, convenience and infotainment, the last called “display” in SSP 254), linked by the gateway inside the instrument cluster J285; speeds, wires and modules are in CAN bus. Diagnosis uses K-wire and L-wire (second K-wire) lines plus, for some units, gateway routing over CAN. Many convenience-side units, J519 and J527 among them, have no K-wire of their own and are reached through J393.
Vehicle electrical system control unit J519
Section titled “Vehicle electrical system control unit J519”
Figure: SSP 254
What J519 does:
- It replaces the old relay-and-fuse central electrics and switches loads with semiconductor outputs (transistors) instead of relays.
- It gets most of its commands over the convenience CAN: turn signals, wipers and headlight flasher come from J527, and flasher requests come from J393.
- The light switch E1 and the hazard switch are wired to it directly. SSP 254 calls the hazard switch E3; the 12.2005 manual calls it E229.
- Because the internal electronics protect each output against faults, the consumers on J519 outputs do not need separate fuses. The English SSP says “separate supply” here; the context means fusing.
- Self-diagnosis is under address word 09. J519 has no K-wire, so the tester reaches it through J393 over the convenience CAN, and J393 must work for 09 to be diagnosed.
The SSP 254 screenshot shows part number 8E0 907 279 B for J519.
Versions and functions
Section titled “Versions and functions”SSP 254 lists three J519 variants:
- “lowline”, standard;
- “lowline” for cars with headlight washers;
- “highline”, for cars with the driver information system (DIS/FIS).
| Function | Lowline | Highline |
|---|---|---|
| Wash/wipe control and interval | ✓ | ✓ |
| Turn signal and hazard control | ✓ | ✓ |
| Horn relay and load-reduction (X-contact) relay drive | ✓ | ✓ |
| Parking lights L/R, side lights L/R | ✓ | ✓ |
| Main beam L/R and headlight flasher | ✓ | ✓ |
| Number-plate light | ✓ | ✓ |
| Dipped beam, front fog, rear fog | conventional wiring and fuses straight from the light switch | ✓ (separate output per lamp) |
| Rear lights, reversing lights, brake lights | conventional | ✓ (separate output per lamp) |
| Driver information system bulb-failure messages | – | ✓ |
Highline-only behaviour:
- Combined brake/tail bulb. Only the 21 W filament of the twin-filament bulb is used. For the tail-light function, J519 dims it to the equivalent of about 5 W with a PWM signal. The second rear light can therefore be monitored, and a failed brake light is reported in the DIS.
- Bulb-failure messages. J519 sends them to the cluster over the convenience CAN. The cluster shows which bulb has failed and where on the car (see Instrument cluster).
- Country-specific lighting is set by coding.
- Light-switch fallback. If the light switch reading is implausible, J519 switches on the side lights and dipped beam automatically.
Fault-finding notes:
- Some lamp outputs are pulsed until the circuit is closed again, so a multimeter cannot measure open-circuit voltage on them. Use an oscilloscope (DSO).
- J519 records a bulb fault only while it is present. Nothing needs erasing after changing a bulb, and SSP 254 says the fault memory should not be erased for this.
Turn signals and hazard lights
Section titled “Turn signals and hazard lights”- The hazard button is wired to J519, which runs the hazard flasher by itself.
- If the driver signals while the hazards are on (for example when towing), the turn signal takes priority for that time.
- With the ignition off, the hazards use shorter on-times to save current.
- Lane-change (“motorway”) flash: a brief tap of the lever gives three flashes.
- The tick comes from an acoustic relay inside the cluster.
- These flash patterns are requested by J393 over the convenience CAN and carried out by J519:
- anti-theft alarm;
- central-locking lock/unlock confirmation;
- key-learning;
- crash;
- panic (USA only).
Wash/wipe
Section titled “Wash/wipe”- The wiper relays are inside J519.
- The washer interval is speed-dependent with 4 stages.
- Re-wipe happens automatically 5 s after washing.
- The washer reservoir is in two parts. With headlight washers, an extra level sensor lets J519 stop the headlight-washer pump (V11) before it runs dry. In highline cars the same sensor feeds the Auto-Check display.
The 12.2005 manual’s level switch is F77, wired to the cluster on T32/1. SSP 254 names the washer level sender G33 and the washer pump V58; neither code is in the database. The manual’s pumps are V5 (windscreen) and V11 (headlights).
Trailer recognition J345
Section titled “Trailer recognition J345”Trailer lights need the separate control unit J345, which converts J519’s lighting messages on the convenience CAN into trailer-socket outputs.
- Do not tap the trailer socket into the car’s lighting wires. J519’s processor would detect it as a fault.
- J345 is diagnosed through J519 (address 09).
- If communication between J345 and J519 fails, the rear lights are switched on as a warning.
Function circuit diagrams
Section titled “Function circuit diagrams”SSP 254 has simplified function diagrams for J519 in its lowline and highline versions, and for the steering column module at maximum equipment. They are colour-coded:
- input signal;
- output signal;
- positive supply;
- earth;
- CAN.
They are useful for understanding the system, not for repairs. For actual wires and pins use the factory diagrams:
| B6 | B7 | |
|---|---|---|
| Basic equipment, lowline | 3 (MY 2003), 18 (MY 2004) | – |
| Basic equipment, highline | 302 (MY 2002), 4 (MY 2003), 19 (MY 2004) | – |
| Standard equipment | – | 62 (from 11/2004), 109 (MY 2006) |
Component code differences between SSP 254 and the manual:
| Part | SSP 254 | Manual |
|---|---|---|
| Load-reduction relay | J59 (function diagram); its block diagram says “relay for X contact J18” | J59 |
| Horns | H2/H4 (block diagram), H2/H7 (function diagram) | H2 high-tone, H7 low-tone, horn relay J4 |
| Reversing light switch | F4 | F4 |
| Brake light switch | F | F |
Steering column switch module J527
Section titled “Steering column switch module J527”
Figure: SSP 254
The compact module needs less wiring and space than before and, for the first time, can be self-diagnosed. It contains:
- turn signal switch (E2);
- wiper switch (E) with interval potentiometer;
- a separate cruise control lever (E45), on the left below the turn signal lever. Lamp K31 in the cluster shows when cruise is controlling speed;
- the coil spring (clock spring) for the driver’s airbag;
- the steering angle sender G85 for ESP. It reads the angle optically and puts it on the drive CAN (see SSP 204 for the principle);
- the electronics J527, which turn switch positions into drive and convenience CAN messages.
How it works:
- Switch positions are read by voltage coding: each position puts a different resistance in circuit. J527 decodes this and sends the commands to J519 over the convenience CAN.
- The ignition lock signals arrive as discrete wires and J527 puts them on the convenience CAN. The gateway passes them on to the drive and infotainment buses. The terminals are:
- P (parking light);
- 86s (key inserted);
- 75 (load reduction);
- 15 (ignition on);
- 50 (starter).
- Multi-function / tiptronic steering wheel: the buttons are read by the steering wheel electronics J453 with operating unit E221, which is included in J527’s self-diagnosis. SSP 254’s function diagram also shows the heated steering wheel Z36 and the horn contact.
- The module must be coded.
- Address word 16 (“steering column electronics”). It is reached over the convenience CAN through J393, because there is no K-wire to J527.
J527’s 16-pin connector T16a in the wiring database:
| Pin | Function |
|---|---|
| 1 | Earth |
| 2 | Terminal 30 via fuse S13 |
| 8 / 9 | Convenience CAN low / high |
| 10 / 11 | Drive CAN high / low |
| 12 | Line from ignition switch terminal 75 (shared with J519). The database labels it terminal 15 in some diagrams |
| 13 | Terminal 15 |
| 14 | 86s (also to J285 T32/22) |
| 15 | Terminal 50 |
| 16 | P |
In the B6 diagrams, a 4-pin connector T4e on J527 carries the driver-airbag circuit from J234 through the coil spring F138 to igniter N95 (manual p. 915). The B7 diagrams additionally show the sport-programme button E541 on T16a/4.
Codes E, E2, E45, E221, G85, J453, K31 and Z36 appear in SSP 254 but are not in the wiring database, so they are not linked.
Multi-communication bar
Section titled “Multi-communication bar”
Figure: SSP 254
The B6 saloon introduced the multi-communication bar (MCB), which puts every aerial along the top edge of the rear window so none show outside. It holds:
- the aerial module, which contains:
- aerial diversity;
- amplifier for the four radio aerials (FM1–4, AM);
- four TV aerial amplifiers;
- the remote central-locking aerial;
- the auxiliary-heater telestart aerial;
- the GPS aerial;
- the GSM (phone) aerial.
The aerial conductors are printed on the rear window and meet the amplifier through spring contacts. The GPS and GSM aerials sit at the top of the glass but do not use printed conductors. The telematics emergency aerial is at the rear bumper.
In the 12.2005 manual the corresponding parts are:
- antenna selection control module J515, behind the roof-end trim at the rear window;
- GPS aerial R50 and phone aerial R65, at the same spot;
- central-locking aerial R47;
- the USA telematics diagrams (305, 129) add a second phone aerial R127 under the rear bumper cover.
The Avant rear diagrams (311, 53) show antenna modules R108/R109 behind the luggage-compartment side trims. SSP 254 describes the MCB for the saloon only.
The TV tuner picks whichever of its four tuners has the best picture and sound, switching within one scan line. It gets control commands over the navigation system’s own data bus and passes picture and sound over ordinary wiring. It is not on the infotainment CAN. Address word 57: coding sets the video standard, and final control diagnosis switches the aerials on one at a time to find a faulty one.
Part numbers in this article
| Number | Name in the catalogue | Illustrations |
|---|---|---|
8E0 907 279 B | Not in the loaded part of the catalogue. The link decodes the number. | |
The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J519 | Vehicle Electrical System Control Module | B6 and B7 | Behind driver's storage compartment |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J345 | Control Module for towing sensor | B6 and B7 | Wired into the instrument panel wiring harness |
J59 | Load Reduction Relay | B6 and B7 | Relay carrier (9-position) with vehicle voltage control module, through 2005 MY, position 6 (black socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
J4 | Horn Relay | B6 and B7 | Relay carrier (9-position) with vehicle voltage control module, through 2005 MY, position 3 (blue socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position) |
H2 | High Tone Horn | B6 and B7 | Behind the headlamp assembly |
H7 | Low Tone Horn | B6 and B7 | Behind the headlamp assembly |
E1 | Light switch | B6 and B7 | Instrument panel, left of the steering wheel |
E229 | Switch for emergency flasher | B6 and B7 | Centre console switch row |
F | Brake Light Switch | B6 and B7 | In footwell at pedal bracket next to the brake pedal |
F4 | Back-Up Light Switch | B6 and B7 | On the transmission |
V | Windshield Wiper Motor | B6 and B7 | Plenum chamber, below the windshield |
V5 | Windshield Washer Pump | B6 and B7 | Front, at the washer fluid reservoir |
V11 | Headlight Washer Pump | B6 and B7 | Front, at the washer fluid reservoir |
F77 | Windshield Washer Fluid Level Warning Switch | B6 and B7 | Front, at the washer fluid reservoir |
D | Ignition/Starter Switch | B6 and B7 | On the steering column, electrical part of the ignition lock |
J234 | Airbag Control Module | B6 and B7 | Below centre console, in front of handbrake lever |
J104 | ABS Control Module (w/EDL) | B6 and B7 | In engine compartment, on hydraulic unit, front left |
J515 | Antenna Selection Control Module | B6 and B7 | At rear window, behind roof frame trim |
R50 | Antenna for Navigation System (GPS) | B6 and B7 | At rear window, behind roof frame trim |
R65 | Antenna for Telephone | B6 and B7 | At rear window, behind roof frame trim |
R47 | Central Locking and Anti-theft Alarm System Antenna | B6 and B7 | Routed from the Comfort System Central Control Module -J393- |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 36–57 and 72–73.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database