VCDS controller addresses
Which VCDS address answers for which control unit on the A4 B6/B7, and the login, coding and adaptation basics the retrofit guides use.
A VCDS address is the logical “door” a scan tool knocks on, for example 17 – Instruments. The table maps each address on the A4 B6/B7 sedan and Avant to the control unit that answers it, using the wiring-manual component codes. Presence follows the Ross-Tech application chart: “Y” means fitted to every car, “opt.” means only if equipped.
Address table
Section titled “Address table”| Addr | VCDS name | Control unit (wiring manual) | B6 | B7 | Notes |
|---|---|---|---|---|---|
| 01 | Engine | J220 (B6) / J623 (B7) | Y (KWP-2000) | Y (CAN or K, by engine) | Cruise enable here, see cruise retrofit |
| 02 | Auto Trans | J217 | opt. | opt. (CAN or K) | Tiptronic and multitronic |
| 03 | ABS Brakes | J104 (Bosch 5.7 on 8E) | Y | Y (CAN or K) | G85 basic setting is done here, below |
| 08 | Auto HVAC | J255 Climatronic | Y | Y | |
| 09 | Cent. Elect. | J519 | Y | Y | Lighting, DRL, chassis coding |
| 0F | Digital Radio | Satellite radio R146 | – | opt. | B7 only |
| 11 | Engine II | J624 | – | RS4 only | Second ECM of the RS4 V8 |
| 15 | Airbags | J234 | Y (KWP-2000) | Y (CAN or K) | |
| 16 | Steering wheel | J527 | Y | Y (K-line only) | Present even without wheel buttons |
| 17 | Instruments | J285 | Y | Y | Also immobiliser and gateway (CAN installation lists) |
| 18 | Aux. Heat | J364 | opt., 2nd K | opt., 2nd K | |
| 19 | CAN Gateway | — | not present | not present | Gateway is built into 17 |
| 22 | AWD | — | not present | not present | quattro is purely mechanical |
| 25 | Immobilizer | (in 17) | in cluster | in cluster | No separate unit |
| 26 | Auto Roof | Sunroof J245? | opt. | opt. | Ross-Tech’s chart shares this row with the Cabriolet’s soft top; unit mapping unconfirmed |
| 35 | Centr. Locks | — | not present | not present | Functions moved to 46 |
| 36 | Seat Mem. Drvr | J136 | opt., 2nd K | opt. | |
| 37 | Navigation | J401 (RNS-D / RNS-E) | opt., 2nd K | opt. | |
| 45 | Inside Monitor | Interior monitoring G303 | Y | Y | Sensitivity in adaptation ch. 01 (B6 page) |
| 46 | Central Conv. | J393 comfort module | Y | Y | Comfort functions; see coding |
| 55 | Xenon Range | J431 | opt., 2nd K | opt., 2nd K or CAN | Xenon / Bi-Xenon cars only |
| 56 | Radio | R | Y, 2nd K | Y, 2nd K | |
| 57 | TV Tuner | — | – | opt. | |
| 65 | Tire Pressure | J502 | – | opt., 2nd K | |
| 67 | Voice Control | J507 | – | opt. | |
| 69 | Trailer | J345 | – | opt. (CAN) | |
| 75 | Telematics / Emerg. call | J526 | opt. | opt. | US telematics |
| 76 | Park Assist | J446 | opt., 2nd K | opt., 2nd K | |
| 77 | Telephone | J412 / J526 / R36 | opt. | opt. | Depends on the phone preparation fitted |
Interfaces and bus notes
Section titled “Interfaces and bus notes”- B6: everything is diagnosed over the K-line. The OBD socket (diagram 312) has two K-lines, T16/7 and T16/15. Radio, navigation, seat memory, park assist, headlight range and aux heater sit on the second K-line. An old single-K cable will not see them; Ross-Tech says a dual-K interface is required. The B6 info page also says that 15 (airbags) and 01/02 use KWP-2000.
- B7: the OBD socket (diagram 61) also carries the drivetrain CAN on T16/6 and T16/14, wired to the cluster. Engine, gearbox, ABS and airbag can be reached over CAN. 16 (steering wheel) stays K-line only, and 56, 65 and 76 stay on the second K-line. Ross-Tech notes that a KII-USB will not reach every module on a B7, and Micro-CAN does not work on B6 or B7.
Login, coding and adaptation basics
Section titled “Login, coding and adaptation basics”Terms used in the retrofit guides:
- Coding (07): a short number (5 or 7 digits) or a long-coding byte string. It tells a module what is fitted.
- Login / Security Access (11 or 16): a code that unlocks protected coding, basic settings or functions. For example, 11463 on the engine ECU enables cruise control.
- Adaptation (10): a numbered channel holding one value, e.g. cluster channel 062.
- Basic Settings (04): a guided calibration run on a measuring-value group.
Before changing anything, save an Auto-Scan and write down the original coding of every module you touch.
Steering wheel (16)
Section titled “Steering wheel (16)”Coding is five digits, 0abcd (Ross-Tech):
| Digit | Meaning | Values |
|---|---|---|
| a (0?xxx) | Steering wheel | 0 standard, 1 3-spoke sport, 2 MFSW radio, 3 MFSW radio+phone, 4 MFSW radio+phone+voice, 5 MFSW radio+voice |
| b (0x?xx) | Options | +1 Tiptronic |
| c (0xx?x) | Trip computer / cruise | 0 none, 1 trip computer, 2 cruise, 4 trip computer + cruise |
| d (0xxx?) | Rear wiper | 1 sedan, 2 Avant |
A replacement J527 has to learn the VIN: in adaptation channel 081, enter 00111 and save.
Instrument cluster (17): channel 062 for the telephone display
Section titled “Instrument cluster (17): channel 062 for the telephone display”Channel 062 is the infotainment CAN installation list. It is a sum of bits: radio +1, telephone +2, navigation +4, telematics +8, and +16 for a second instrument-cluster entry. To make the cluster show telephone information after a phone retrofit, add 2 to the existing value. For example, a car with radio only (1) becomes 3. Channels 060 (drivetrain CAN) and 061 (comfort CAN) work the same way for their buses (Ross-Tech).
Steering angle sensor G85 after a steering-wheel swap
Section titled “Steering angle sensor G85 after a steering-wheel swap”On the 8E the steering angle sensor G85 sits at the steering column module J527 (it is drawn with J527 in the manual). It reports over CAN to the Bosch 5.7 ESP unit. Removing the wheel or the clock spring, or replacing J527, can upset the zero point. The ESP warning light then stays on, typically with fault 00778. Ross-Tech’s procedure for the Bosch 5.7 on the A4 (8E) (Ross-Tech):
- Start the engine. Turn the wheel to both end stops, then set it straight ahead. Do all of the following steps without switching off the ignition or leaving address 03.
- 03 → Measuring Blocks (08), group 005, field 1 (G85). It should read about 0.0°. The tolerance is ±5° with the wheels straight.
- Login (11): 40168.
- Basic Settings (04): group 001.
- Read and clear the fault codes. Fault 01486 “System Function Test Active” may appear afterwards; Ross-Tech calls this normal.
Group 001 is right for the Bosch 5.7. Many other VW/Audi ESP units (MK60, for example) use group 060, and generic guides often give that number. Ross-Tech also warns that some Bosch 5.7 units show no live G85 value: if group 005 stays stuck at −2.5°, set the wheels as straight as you can and carry on.
ABS/ESP coding (03)
Section titled “ABS/ESP coding (03)”Bosch 5.7 coding depends on the brake package (PR codes 1LJ/1LT/1LX/…), the engine and the gearbox, and needs a matching login first. Ross-Tech has the table. Example: a BFB engine with 1LT brakes and multitronic uses login 09399 and coding 04499. Swapping a wheel or J527 does not normally change the ABS coding.
Comfort module (46)
Section titled “Comfort module (46)”Ross-Tech’s (older, B6) notes put the comfort options in coding plus adaptation channel 062. Example: a US 3.0 with original coding 11788 gets “comfort open/close with the remote” by adding 64 to the coding. Ross-Tech tested on a 2002 car and warns that 2003+ cars may differ.
Central electronics (09)
Section titled “Central electronics (09)”On the B7 (Ross-Tech):
| Digit | Meaning |
|---|---|
| 1 | Body: sedan, Avant or Cabriolet |
| 2 | Rain/light sensor G397 |
| 3 | Trailer hitch |
| 4 | Headlights and DRL: halogen with or without DRL, Bi-Xenon variants |
| 5 | Country |
Adaptation channels cover coming-home time (001), the DRL on/off and dimming (005–008), and the rain/light sensor (020–022).
See also: B6 vs B7 electrical differences, CAN bus, instrument cluster.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
G303 | Radar Interior Monitoring Control Module 1 | B6 and B7 | Wired into the roof wiring harness |
J220 | Motronic Engine Control Module (ECM) | B6 only | In electronics box, plenum chamber |
J623 | Engine Control Module (ECM) | B7 only | Under the plenum chamber cover |
J217 | Transmission Control Module (TCM) | B6 and B7 | In electronics box, plenum chamber |
J104 | ABS Control Module (w/EDL) | B6 and B7 | In engine compartment, on hydraulic unit, front left |
J255 | Climatronic Control Module | B6 and B7 | Integrated with Interior Temperature Sensor Fan -V42- and Instrument Panel Interior |
J519 | Vehicle Electrical System Control Module | B6 and B7 | Behind driver's storage compartment |
J234 | Airbag Control Module | B6 and B7 | Below centre console, in front of handbrake lever |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
J364 | Control module for auxiliary heater | B6 and B7 | Wired into the instrument panel wiring harness |
J245 | Power Sunroof Control Module | B6 and B7 | Roof, at the sunroof / front headliner |
J136 | Memory Seat Control Module | B6 and B7 | Under the driver's seat, on the seat frame |
J401 | Navigation System with CD Drive Control Module | B6 and B7 | In centre console |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J431 | Headlight Range Control Module | B6 and B7 | Behind glove box |
R | Radio | B6 and B7 | Top of the center console |
J502 | Tire Pressure Monitoring Control Module | B7 only | Wired into the instrument panel wiring harness |
J345 | Control Module for towing sensor | B6 and B7 | Wired into the instrument panel wiring harness |
J446 | Control module for parking aid | B6 and B7 | On rear cross panel, luggage compartment, left, behind trim near left rear light |
J526 | Telephone/Telematic Control Module | B6 and B7 | In Electronics box under the front passenger seat |
J412 | Control module for operating electronics, Telephone | B6 only | Centre console / armrest, telephone installation |
J624 | Engine Control Module (ECM) 2 | B7 only | Under the plenum chamber cover |
J507 | Speech Input Control Module | B6 only | In the electronics box under the front passenger's (right front) seat |
R146 | Satellite Radio | B6 and B7 | In luggage compartment left, behind side trim |
Sources
- Ross-Tech – Audi A4/S4/RS4 application chartAddress list for B6 and B7 (present / if equipped / 2nd K-line / CAN). Main source for the table.
- Ross-Tech – Audi A4/S4 B6/8E VCDS info pageOlder (2010) B6 notes on protocols (KWP-1281/KWP-2000), dual K-line, address 35 moved to 46. Tested on a 2002 car.
- Ross-Tech Wiki – Audi A4 (8E) Steering WheelAddress 16 coding and channel 081 VIN learning.
- Ross-Tech Wiki – Audi A4 (8E) Instrument Cluster (8EC/8ED/8HE)Address 17 coding and adaptation channels 060–062, 099. The page is titled for B7 types.
- Ross-Tech Wiki – Audi A4 (8E) Brake Electronics (Bosch 5.7)Address 03 coding logins and the G85 steering angle sensor calibration.
- Ross-Tech Wiki – Audi A4 (8E) Central Electronics (8EC/8ED)Address 09 coding (B7).
- Ross-Tech Wiki – Cruise Control Retrofitting (8E)
- vag-coding.net – VCDS: Basic setting of G85 steering angle sensorFault 00778 as the typical symptom; group 001 for pre-2005 A4/A6/A8 vs group 060 for MK60 platforms.
- Audi A4 Wiring Diagrams and Component Locations (US manual, 12.2005)Component codes for each address and the diagnostic connector wiring.