Running gear, brakes and ESP
B6 axles, engine and gearbox mountings, and the Bosch ESP 5.7 with brake assistant from SSP 254, with the ESP sensors in the wiring data.
Four-link front axle
Section titled “Four-link front axle”- Every transverse link and the pivot bearing (wheel carrier) is aluminium. SSP 254 puts the weight saving at about 8.5 kg for the front axle.
- The wheel bearing is bolted to the pivot bearing with four bolts. The hub can be pressed in and out.
- The strut top mount is a large rubber bearing in two parts. The inner part connects to the piston rod. The larger outer part isolates the shock absorber acoustically.
- The figure on page 26 of SSP 254 also labels an aluminium mounting bracket and an aluminium spring plate.
Trapezium-link rear axle
Section titled “Trapezium-link rear axle”The trapezium-link rear axle, previously quattro-only, is used with largely identical parts on both front-wheel drive and quattro cars. The two versions differ only in:
- the axle mounting;
- the wheel carrier and bearings:
- front-wheel drive: a wheel-bearing unit with integral hub, on a stub axle forged in one piece with the wheel carrier;
- quattro: pressed-in double-row angular-contact ball bearings with conventional hubs.
Toe and camber are both adjustable at the rear. SSP 254’s figures mark where.
Engine and gearbox mountings
Section titled “Engine and gearbox mountings”- Three-point mounting: two hydraulically damped engine mounts and one gearbox mount. The diesel engine mounts are electrically controlled.
- The engine mounts bolt directly to the longitudinal members through die-cast aluminium brackets.
- The gearbox mount is a conventional rubber bearing on a body-mounted aluminium carrier (hollow sand-cast).
- An aluminium cross member is bolted to the body and to the rear subframe mountings. It supports the gearbox mount over a longer lever arm, which helps vibration and load-change behaviour, and doubles as a body-stiffening tunnel bridge.
- A torque member is also shown in the figure.
SSP 254 notes that this three-point layout is used for every engine/gearbox combination except those with the 01V 5-speed automatic.
Brake system: Bosch ESP 5.7
Section titled “Brake system: Bosch ESP 5.7”The B6 introduced Bosch ESP 5.7:
- the hydraulic unit and the control unit (J104) form a single assembly, at the front left of the engine bay;
- the charging (pre-charge) pump is deleted. Earlier systems used it (ESP hydraulic pump V156);
- a brake assistant is built in.
Why the pre-charge pump could go. Brake fluid becomes very viscous when cold. Without a pre-charge pump, the earlier ABS return pump (V39) could not draw in enough fluid. ESP 5.7 solves this with:
- a two-stage return pump: its stepped, double-acting piston sucks on both strokes, so the suction flow is almost continuous, peak suction pressure is lower and cavitation is avoided;
- larger brake-line cross-sections;
- a larger central valve in the master cylinder.
The inlet and outlet valves in the hydraulic modulator are no longer simply switched on and off. They are regulated by the supplied voltage, which gives finer control on very slippery surfaces such as ice.
Brake assistant
Section titled “Brake assistant”Accident research shows that most drivers do not press the pedal hard enough in an emergency. The brake assistant detects emergency braking from how fast the brake pressure rises. It then raises the pressure automatically into the ABS control range.
- Phase 1: if the pressure rise exceeds a set rate, J104 runs the ABS return pump and opens the relevant solenoid valves to build pressure, much as it does for the electronic differential lock (EDL).
- Phase 2: when the driver’s pressure falls below a threshold, the system pressure drops back to whatever the driver is applying.
SSP 254 names the sensor as G294, “brake servo pressure sensor”.
ESP sensors in the wiring data
Section titled “ESP sensors in the wiring data”| Signal | B6 (diagrams 309, 14) | B7 (diagrams 52, 104) |
|---|---|---|
| Steering angle | G85, inside the steering column module J527. It is optical and sends its value on the drive CAN. G85 is drawn in the manual but has no database entry | same |
| Yaw rate | G202 (sensor cluster) | G202 together with G200 (lateral acceleration) |
| Brake pressure | G201 on the hydraulic unit | – (not in the B7 diagrams) |
| Brake light / pedal | F | F and brake pedal switch F47 |
| ESP/ASR off button | E132 | E132 |
| Wheel-speed sensors | G44–G47 | not itemised in the extracted data |
The B6 diagram 14 is the 4.2 l (S4) version of the B6 ESP wiring. The cluster gets the ESP warning signal on T32/16 and the ABS warning on T32a/22 (see Instrument cluster).
Brake service details
Section titled “Brake service details”- Brake fluid reservoir: held by an extra screw. It has a new maintenance opening for drawing fluid out of both chambers, using the brake filler/bleeder VAS 5234.
- Brake light switch (F): bayonet-mounted on the pedal bracket, with a new adjustment procedure:
- Turn the switch anti-clockwise to remove it. This also releases the push-rod catch.
- Pull the push rod out to its stop. This is the basic setting.
- Insert the switch and turn it clockwise. The catch locks automatically.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J104 | ABS Control Module (w/EDL) | B6 and B7 | In engine compartment, on hydraulic unit, front left |
G201 | Brake pressure sensor 1 | B6 only | Bolted to the hydraulic unit |
G202 | Sender for Rotation Rate | B6 and B7 | Components integrated in one housing |
G294 | Brake Booster Pressure Sensor | B6 and B7 | Wired into the engine wiring harness |
F | Brake Light Switch | B6 and B7 | In footwell at pedal bracket next to the brake pedal |
F9 | Parking Brake Warning Light Switch | B6 and B7 | On the parking brake lever unit |
E132 | Anti-Slip Control Switch | B6 and B7 | On the center console |
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 26–34.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseABS/ESP diagrams 309 and 14 (B6), 52 and 104 (B7).