Data quality
The wiring pages are extracted from the factory manual (Audi A4 Wiring Diagrams and Component Locations, edition 12.2005) by software. This page counts how much of that is stated by the manual, worked out, or guessed, and lists what has been corrected by hand and what is still known to be wrong. The numbers are worked out from the data each time the site is built.
What the data holds
| Components | 584 |
|---|---|
| Their pins | 3,220 |
| Splices | 142 |
| Ground points | 74 |
| Connectors | 197 |
| Diagrams | 126 |
| Wires drawn on the sheets | 12,829 |
| Nets (wires traced across sheets) | 3,093 |
What each wire carries
Each net has a function label, and the label says how it was worked out.
| Function | Nets | Share |
|---|---|---|
| Stated by the manual stated | 901 | 29 % |
| Derived from terminal markings, fuses or the colour code derived | 206 | 7 % |
| Only what the wire connects endpoints only | 1,949 | 63 % |
| No label | 37 | 1 % |
“Only what the wire connects” is what a component page shows as “not stated” under Function: the manual draws the wire but does not say what it carries.
Guesses and loose ends
| Wire ends whose component is a guess (its label is not right at the symbol) | 2,191 on 783 nets |
|---|---|
| Unresolved wire ends (a pin with no component, or a wire that stops at a symbol the extraction does not know) | 766 on 271 nets |
A net page says how many of each it has. A check by eye of 24 guesses found about 21 clearly right and none clearly wrong (see the open problems below).
Corrections applied
70 corrections, each read from a page of the manual and applied when the data is rebuilt. By kind:
- Wire end given to its pin: 35
- Component added: 21
- Splice or ground point relabelled: 6
- Pins given back to their part: 3
- Wrong join refused: 2
- Net relabelled: 2
- Component renamed: 1
Every correction, with the pages it changed and its evidence
| Correction | Changed | Evidence |
|---|---|---|
c-0001Splice or ground point relabelled A159: L-line (diagnosis), to diagnostic connection T16 pin 15 | A159 | p. 360 (headlight range control): legend 'A159 Wire connection (L), in instrument panel wiring harness' and 'T16 16-Pin Connector, black, diagnostic connection'; A159 is drawn on the 0,22/0,35 gn/bl wire from J431 pin 14 to T16/15. p. 18 draws the same splice on gn/bl to T8/3 (radio connector III). The '(L)' is the diagnosis L wire, not terminal L (left turn signal), which the label rule had read it as. |
c-0002Splice or ground point relabelled D113: Engine control module supply from fuse S102 (15 A) to J623 and J624 | D113 | p. 615 (4.2 FSI BNS): legend 'D113 Connection 11 (in engine compartment wiring harness)'; the next legend row, 'Data bus wiring (CAN bus)', is the key to a wiring symbol (its glyph reads as '?' in the text layer) and was read as part of D113's name. The sheet draws S102 (Engine Control Module (ECM) Fuse, 15A) pin 2, 1,5 ro/bl to D102 (J623 T94/3, /5, /6), then 4,0 ro/sw to D113, which feeds J624 T94a/3, /5, /6 on 2,5 ro/bl. Same on pp. 812 and 813 (2,5 ro/sw; D113 continued as a line to J624). |
c-0003Splice or ground point relabelled D108: Oxygen sensor heater supply from fuse S73 (15 A) | D108 | p. 613 (4.2 FSI BNS): legend 'D108 Connection 6 (in engine compartment wiring harness)' followed by the symbol-key row 'Data bus wiring (CAN bus)', which was read as part of D108's name. The sheet draws D108 on the gn/sw wire from S73 (Heated Oxygen Sensor (HO2S) Circuit Breaker, 15A) pin 2 to the heaters Z19 (T6/4) and Z29 (T4b/1) and refs 254, 260. |
c-0004Splice or ground point relabelled D108: Oxygen sensor heater supply from fuse S73 (15 A) | D108 | p. 810 (4.2 FSI BNS from 2007): same drawing and legend as p. 613: D108 on gn/sw from S73 pin 2 to Z19 (T6/4), Z29 (T4b/1) and refs 268, 274; the symbol-key row 'Data bus wiring (CAN bus)' glued to D108's legend name. |
c-0005Wrong join refused rail “a” in diagram 35 | how wires join (no page of its own) | pp. 312 to 314 (Comfort system B6): the rail lettered 'a' on p. 312 is the 58s line (A175 'Wire connection (58s)', gr/bl from J285 T32a/17) running off the right edge; on p. 313 it comes in from the left edge and ends at A175. The 'a' rail on p. 314 is a different line: it starts at A146 (Comfort System High-bus Connection, or/gn) and runs off the right edge. The linker joined 313 and 314 by the letter. 'a' is used nowhere else in diagram 35; 312 and 313 stay joined by A175. |
c-0006Wrong join refused rail “a” in diagram 67 | how wires join (no page of its own) | pp. 484 to 486 (Comfort system B7): same layout as pp. 312 to 314: rail 'a' is the A175 (58s) line from J285 T32a/17 on 484 and 485, ending at A175 on 485; on 486 'a' starts at A146 (or/gn). 'a' is used nowhere else in diagram 67; 484 and 485 stay joined by A175. |
c-0018Wire end given to its pin end 72:10#0 → J386 T32c/12 | J386 | p. 72: the bl/li wire to E39 7/KISIF leaves J386 at 'T32c/12', printed on two lines ('T32c/' over '12'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0019Wire end given to its pin end 72:12#0 → J386 T32c/26 | J386 | p. 72: the sw/ws wire to E39 8/KISI leaves J386 at 'T32c/26', printed on two lines ('T32c/' over '26'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0020Wire end given to its pin end 314:11#0 → J386 T32c/12 | J386 | p. 314: the bl/li wire to E39 7/KISIF leaves J386 at 'T32c/12', printed on two lines ('T32c/' over '12'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0021Wire end given to its pin end 314:13#0 → J386 T32c/26 | J386 | p. 314: the sw/ws wire to E39 8/KISI leaves J386 at 'T32c/26', printed on two lines ('T32c/' over '26'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0022Wire end given to its pin end 486:11#0 → J386 T32c/12 | J386 | p. 486: the bl/li wire to E39 7/KISIF leaves J386 at 'T32c/12', printed on two lines ('T32c/' over '12'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0023Wire end given to its pin end 486:13#0 → J386 T32c/26 | J386 | p. 486: the sw/ws wire to E39 8/KISI leaves J386 at 'T32c/26', printed on two lines ('T32c/' over '26'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0024Wire end given to its pin end 696:9#0 → J386 T32c/12 | J386 | p. 696: the bl/li wire to E39 7/KISIF leaves J386 at 'T32c/12', printed on two lines ('T32c/' over '12'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0025Wire end given to its pin end 696:10#0 → J386 T32c/26 | J386 | p. 696: the sw/ws wire to E39 8/KISI leaves J386 at 'T32c/26', printed on two lines ('T32c/' over '26'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0026Wire end given to its pin end 997:10#0 → J386 T32c/12 | J386 | p. 997: the bl/li wire to E39 7/KISIF leaves J386 at 'T32c/12', printed on two lines ('T32c/' over '12'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0027Wire end given to its pin end 997:12#0 → J386 T32c/26 | J386 | p. 997: the sw/ws wire to E39 8/KISI leaves J386 at 'T32c/26', printed on two lines ('T32c/' over '26'); the extraction read the pin as 'T32c/' on V14, which is drawn inside J386. |
c-0028Component added G384 · Vehicle Inclination Sensor | G384 | Listed in the legends of pp. 72, 314, 486, 695, 997 ('G384 Vehicle Inclination Sensor') and drawn inside the J393 box; it has no wire of its own on these sheets, its pins were J393's (c-0007 to c-0009). |
c-0029Component added V14 · Left Window Motor | V14 | Listed in the legends of pp. 72, 314, 486, 696, 997 ('V14 Left Window Motor' / 'Left window regulator motor') and drawn inside the J386 box; its pins were J386's (c-0010, c-0011). V14 is also a splice code in other diagrams ('Wire connection (shielding), in CD-changer wiring harness'), which is a junction, not this part. |
c-0030Component added V15 · Right Window Motor | V15 | Listed in the legends of pp. 78, 320, 492, 702, 1003 ('V15 Right Window Motor') and drawn inside the J387 box; its pins were J387's (c-0012, c-0013). |
c-0031Component added V26 · Motor for window regulator, rear, left | V26 | Listed in the legends of pp. 81, 323, 495, 705, 1006 and drawn inside the J388 box; its pins were J388's (c-0014, c-0015). |
c-0032Component added V27 · Motor for window regulator, rear, right | V27 | Listed in the legends of pp. 83, 325, 497, 707, 1008 and drawn inside the J389 box; its pins were J389's (c-0016, c-0017). |
c-0033Net relabelled F224 Driver's Lumbar Support Pressure Switch pin 2 — line to J810 T32j/2 (switch line, not a CAN wire) | p. 731: F224 is a switch drawn between J810 T32j/30 (0,5 or/ge, pin 1) and J810 T32j/2 (0,5 or/gn, pin 2). The wire carries no CAN marking and reaches no other part; the label rule had read its or/gn colour as Comfort CAN High. | |
c-0034Net relabelled F225 Front Passenger's Lumbar Support Pressure Switch pin 2 — line to J720 T32k/2 (switch line, not a CAN wire) | p. 732: F225 is a switch drawn between J720 T32k/30 (0,5 or/ge, pin 1) and J720 T32k/2 (0,5 or/gn, pin 2). The wire carries no CAN marking and reaches no other part; the label rule had read its or/gn colour as Comfort CAN High. | |
c-0035Splice or ground point relabelled B229: CAN High of J431's own bus to the cornering light motors V318 and V319 (not the drivetrain CAN) | B229 | p. 711 (Can-Bus wiring, B7) and p. 468 (Bi-Xenon headlights with cornering light): legend 'B229 High-Bus Connection (in interior wiring harness)'. B229 joins J431 pin 18 (0,35 ws/ro) to V318 pin 1 and V319 pin 1 only; J431 reaches the drivetrain CAN on pins 2 and 3 (or/sw, or/br, via A121/A122). The label rule had made every unnamed High-bus connection 'Drivetrain'. |
c-0036Splice or ground point relabelled B230: CAN Low of J431's own bus to the cornering light motors V318 and V319 (not the drivetrain CAN) | B230 | p. 711 and p. 468: legend 'B230 Low-Bus Connection (in interior wiring harness)'. B230 joins J431 pin 19 (0,35 gn/ro) to V318 pin 2 and V319 pin 2 only; J431's drivetrain CAN pins are 2 and 3. |
c-0037Component renamed G201 → “Brake pressure sensor 1” | G201 | Component Locations p. 1175 (ABS/ESP overview): '5 - Brake Pressure Sensor 1 -G201-, Bolted to the hydraulic unit'; the steering angle sensor is G85 (item 12). The legend of p. 928 (ABS with ESP, B6 from 2002) names G201 'Brake pressure sensor 1'; the legend and title of p. 162 (ABS with ESP, 4.2 l), the same drawing (97-55244), print 'Steering -1- Angle Sensor', which the label step had taken. |
c-0038Wire end given to its pin end 405:6#1 → N95 + | N95 | p. 405 (Driver and Front Passenger Airbags): the wire from F138, from J234 pin 23 via T4e/1 ends at the contact of N95 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0039Wire end given to its pin end 405:9#1 → N95 - | N95 | p. 405 (Driver and Front Passenger Airbags): the wire from F138, from J234 pin 22 via T4e/2 ends at the contact of N95 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0040Wire end given to its pin end 405:10#1 → N250 + | N250 | p. 405 (Driver and Front Passenger Airbags): the wire from F138, from J234 pin 37 via T4e/3 ends at the contact of N250 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0041Wire end given to its pin end 405:13#1 → N250 - | N250 | p. 405 (Driver and Front Passenger Airbags): the wire from F138, from J234 pin 38 via T4e/4 ends at the contact of N250 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0042Wire end given to its pin end 405:14#1 → N131 - | N131 | p. 405 (Driver and Front Passenger Airbags): the wire from T5c/2 from J234 pin 17 ends at the contact of N131 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0043Wire end given to its pin end 405:15#1 → N131 + | N131 | p. 405 (Driver and Front Passenger Airbags): the wire from T5c/1 from J234 pin 18 ends at the contact of N131 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0044Wire end given to its pin end 405:16#1 → N132 - | N132 | p. 405 (Driver and Front Passenger Airbags): the wire from T5c/5 from J234 pin 39 ends at the contact of N132 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0045Wire end given to its pin end 405:17#1 → N132 + | N132 | p. 405 (Driver and Front Passenger Airbags): the wire from T5c/4 from J234 pin 40 ends at the contact of N132 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0046Wire end given to its pin end 633:6#1 → N95 + | N95 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from F138, from J234 pin 23 via T4e/1 ends at the contact of N95 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0047Wire end given to its pin end 633:9#1 → N95 - | N95 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from F138, from J234 pin 22 via T4e/2 ends at the contact of N95 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0048Wire end given to its pin end 633:10#1 → N250 + | N250 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from F138, from J234 pin 37 via T4e/3 ends at the contact of N250 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0049Wire end given to its pin end 633:13#1 → N250 - | N250 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from F138, from J234 pin 38 via T4e/4 ends at the contact of N250 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0050Wire end given to its pin end 633:14#1 → N131 - | N131 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from T5c/2 from J234 pin 17 ends at the contact of N131 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0051Wire end given to its pin end 633:15#1 → N131 + | N131 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from T5c/1 from J234 pin 18 ends at the contact of N131 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0052Wire end given to its pin end 633:16#1 → N132 - | N132 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from T5c/5 from J234 pin 39 ends at the contact of N132 marked '-'; the extraction read the end as an unnamed T-joint. |
c-0053Wire end given to its pin end 633:17#1 → N132 + | N132 | p. 633 (Driver's and Front Passenger's Airbag Igniter): the wire from T5c/4 from J234 pin 40 ends at the contact of N132 marked '+'; the extraction read the end as an unnamed T-joint. |
c-0054Wire end given to its pin end 915:4#1 → N95 + | N95 | p. 915 (B6 airbags and belt tensioners): the wire from F138 (J234 pin 33 via T4e/1) ends at the contact of N95 marked '+' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0055Wire end given to its pin end 915:7#1 → N95 - | N95 | p. 915 (B6 airbags and belt tensioners): the wire from F138 (J234 pin 34 via T4e/2) ends at the contact of N95 marked '-' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0056Wire end given to its pin end 915:8#1 → N131 + | N131 | p. 915 (B6 airbags and belt tensioners): the wire from T4f/1 from J234 pin 37 ends at the contact of N131 marked '+' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0057Wire end given to its pin end 915:9#1 → N131 - | N131 | p. 915 (B6 airbags and belt tensioners): the wire from T4f/2 from J234 pin 38 ends at the contact of N131 marked '-' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0058Wire end given to its pin end 915:11#1 → N153 - | N153 | p. 915 (B6 airbags and belt tensioners): the wire from T2a/2 from J234 pin 62 ends at the contact of N153 marked '-' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0059Wire end given to its pin end 915:12#1 → N153 + | N153 | p. 915 (B6 airbags and belt tensioners): the wire from T2a/1 from J234 pin 61 ends at the contact of N153 marked '+' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0060Wire end given to its pin end 915:13#1 → N154 + | N154 | p. 915 (B6 airbags and belt tensioners): the wire from T2b/1 from J234 pin 64 ends at the contact of N154 marked '+' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0061Wire end given to its pin end 915:15#1 → N154 - | N154 | p. 915 (B6 airbags and belt tensioners): the wire from T2b/2 from J234 pin 63 ends at the contact of N154 marked '-' (printed '--' for minus); the extraction read the end as an unnamed T-joint. |
c-0062Component added N95 · Driver's Airbag Igniter | N95 | Listed in the legends of pp. 405, 510, 633, 722, 726 ('Driver's Airbag Igniter'), 915 and 1021 ('Driver's Side (a)irbag Igniter') and drawn on each; Component Locations p. 1181 '1 - Driver Airbag Igniter -N95-'. Wired on pp. 405, 633, 915 (recoded above); on pp. 510, 722, 726, 1021 it is drawn inside E221 with no extracted wire. |
c-0063Component added N250 · Driver's Airbag Igniter 2 | N250 | Listed in the legends of pp. 405, 510, 633, 722, 726 ('Driver's Airbag Igniter 2') and drawn on each; p. 1181 names N95 and Driver Airbag Igniter 2 together. Wired on pp. 405 and 633 (recoded above); on 510, 722, 726 drawn inside E221 with no extracted wire. |
c-0064Component added N131 · Front Passenger's Airbag Igniter 1 | N131 | Listed in the legends of pp. 405, 633 ('Front Passenger's Airbag Igniter 1') and 915 ('Passenger's Side airbag Igniter 1'), drawn and wired on each (recoded above); p. 1181 '5 - Front Passenger Airbag Igniter 1 -N131-'. |
c-0065Component added N132 · Front Passenger's Airbag Igniter 2 | N132 | Listed in the legends of pp. 405 and 633 ('Front Passenger's Airbag Igniter 2'), drawn and wired on both (recoded above). |
c-0066Component added F138 · Airbag Spiral Spring/Return Spring With Slip Ring | F138 | Listed in the legends of pp. 365, 372, 405, 510, 633, 915, 1021, 1056, 1061 ('Airbag Spiral Spring/Return Spring With Slip Ring'); drawn as the box of spiral springs between T4e and the driver's igniters (pp. 405, 633, 915) and above J527 (pp. 510, 1021). Its contacts carry no pin numbers, so no wire end is recoded to it. Component Locations p. 1181 'B - ... -F138-'. |
c-0067Component added E221 · Control Module in Steering Wheel | E221 | Listed in the legends of pp. 509, 510, 720, 722, 725, 726 ('Control Module in Steering Wheel') and 1020, 1021 ('Control unit in steering wheel'), drawn as the box around the steering-wheel parts. Its inner lines are not extracted, and pp. 509, 720, 725, 1020 have no extracted wires at all. |
c-0068Component added J453 · Multi-function Steering Wheel Control Module | J453 | Listed in the legends of pp. 720, 725, 726 ('Multi-function Steering Wheel Control Module') and drawn inside E221 on them. Its wires (T3m to F350 on p. 726) are inside E221 and not extracted; pp. 720 and 725 have no extracted wires. |
c-0069Component added N201 · Rear Passenger's Side Airbag (driver's side) Igniter | N201 | Listed in the legends of pp. 409, 637 and 919 ('Igniter for side airbag rear, driver's side') and drawn on each. Its three wires from J234 through T4i are extracted, but the igniter's contacts carry no marking, so their ends are left as they are. |
c-0070Component added N202 · Rear Passenger's Side Airbag (front passenger's side) Igniter | N202 | Listed in the legends of pp. 409, 637 and 919 ('Igniter for side airbag rear, passenger side') and drawn on each. Its three wires from J234 through T4j are extracted, but the igniter's contacts carry no marking, so their ends are left as they are. |
c-0071Pins given back to their part K75 T32a → J285 | K75 J285 | K75 (Airbag Malfunction Indicator Lamp) is drawn inside the J285 box (instrument cluster) on p. 23 and p. 921; legend 'T32a 32-Pin Connector, green, on instrument panel insert'. The wires at T32a/2, /3, /7 (p. 23) and T32a/7, /30 (p. 921) end at J285's connector; the extraction gave them to the lamp drawn next to them. Same drawing on the other sheets that carried these ends. |
c-0078Component added K75 · Airbag Malfunction Indicator Lamp (MIL) | K75 | Drawn inside J285 and listed in the legends (pp. 23, 921 among them); its pins were J285's (recode_pins above). The diagrams are those it was drawn in before. |
c-0079Component added G21 · Speedometer | G21 | Drawn inside J285 and listed in the legends (pp. 25, 858 among them); its pins were J285's. The diagrams are those it was drawn in before. |
c-0080Component added G5 · Tachometer | G5 | Drawn inside J285 and listed in the legend of p. 23; its pin was J285's. The diagrams are those it was drawn in before. |
c-0081Component added K2 · Generator (GEN) Warning Light | K2 | Drawn inside J285 and listed in the legends (pp. 23, 112, 529, 622 among them); its pins were J285's. The diagrams are those it was drawn in before. |
c-0082Component added Y8 · Radio Frequency Controlled Clock | Y8 | Drawn inside J285 and listed in the legend of p. 24; its pins were J285's. The diagrams are those it was drawn in before. |
c-0083Pins given back to their part G1 T32 → J285 | G1 J285 | p. 22: G1 (Fuel Gauge) is drawn inside the J285 box; legend 'T32 32-Pin Connector, blue, on instrument panel insert'. The wires at T32/3, /11, /21, /22, /23, /30, /31, /32 end at J285's connector, not at the gauge. |
c-0084Pins given back to their part G3 T32 → J285 | G3 J285 | p. 22: G3 (Engine Coolant Temperature (ECT) Gauge) is drawn inside the J285 box; legend 'T32 32-Pin Connector, blue, on instrument panel insert'. The wires at T32/2, /4, /17, /18 end at J285's connector. |
c-0085Component added G1 · Fuel Gauge | G1 | Drawn inside J285 and listed in the legend of p. 22; its pins were J285's (c-0083). The diagrams are those it was drawn in before. |
c-0086Component added G3 · Engine Coolant Temperature (ECT) Gauge | G3 | Drawn inside J285 and listed in the legend of p. 22; its pins were J285's (c-0084). The diagrams are those it was drawn in before. |
c-0087Wire end given to its pin end 149:9#1 → G266 3 | G266 | p. 149 (4.2 l S4 engine): the 0,35 ro/gr wire from J285 T32/23 through T10a/9 ends at pin 3 of G266 (Oil Level Thermal Sensor); the extraction guessed G169 (Fuel Level Sensor 2), whose pin 3 is the br/ge ground wire next to it. |
How corrections work: docs/corrections.md in the project.
Checked by hand
Nets checked end to end against the manual: 0. Pins: 0. Nothing has been recorded as checked yet: everything on the wiring pages is as extracted (and corrected above), not checked against the car or the sheet by hand.
Known problems still open
33 entries are open in the project’s list of known issues, in 7 groups. The first sentence of each:
Extraction (9 open, 1 fixed)
- 657 pin ends have no component.
- 2,324 splice ends have no code.
- 1,196 wires have no gauge/colour.
- 109 `open` ends, for example spark plug connectors (P) and wires that stop at symbols the extractor does not know.
- 18 sheets have track numbers but no wires (10, 36, 60, 179, 205, 224, 255, 300, 443, 509, 661, 720, 721, 725, 843, 985, 1020, 1050).
- Legends, notes and sheet titles still come from the old extraction and contain bits of the copyright watermark ("... in part or in whole, is not").
- The legend parser glues a symbol-key row to the legend row above it: the key rows whose code column is a glyph rather than a code ("Data bus wiring (CAN bus)", "CAN-Bus (Data bus)" after a `?`, `●` o…
- German terminal names on lock symbols come out garbled ("?ffnen" for "öffnen") in the PDF text layer.
- Airbag sheets: wire ends at parts whose contacts carry no marking stay unnamed T-joints.
Linking and the model (5 open)
- 28 refs without a partner.
- 15 merged nets are flagged `colour_mixed`.
- Page 544 type layouts: two rails drawn on one line can still be joined.
- Merged nets have not been checked against the PDF end to end (that is Phase 6).
- Rail letters are reused within a diagram: a rail lettered "a" that ends on one sheet and a new rail "a" that starts on the next are joined by the linker, which only checks that the two sheets are con…
Labels (7 open, 2 fixed)
- Sheet nets whose label lists a second, contradicting splice name ("also on this net: ..."): 515 before W1b, 489 after it (the 26 nets of the A146 / 58s join are gone).
- 4,544 wires only have an endpoint description ("G62 … — line to J220 pin 93").
- Name-based locations are coarse (an area, not a bracket) and were not checked against the car.
- Connector housing part numbers: not in this manual.
- The location parser attaches a statement to the wrong section heading on pages where a new section starts mid-page (the page number is still right).
- No label was compared with the PDF by eye except the ground bonding on page 7.
- Junction 218's ground point is a tie.
3D car (7 open, 1 fixed)
- No position was checked on a car.
- A route shows which areas a wire passes through, not its real path or length.
- Things sharing a spot (42 fuses in the fuse panel, 34 parts "on the engine") are in code order, not in their real arrangement.
- Sedan and Avant are only partly separable.
- B6 and B7 share one shell and one set of positions, as do all engines.
- Only checked in headless Edge with software WebGL (see the log).
- Location texts that are wrong in phase 7 are wrong here too (the parser attaching a statement to the wrong heading).
Wiki (3 open)
- The Docker image build was not tested (no Docker on the machine it was written on).
- Articles marked "researched" or "community" were not tried on a car.
- `site/src/content/docs/about.md` still tells readers to see the former project plan, which is now `docs/history.md`.
Parts catalogue (1 open)
- 24 tests in `tools/tests/test_review_fixes.py` (the regression tests for the phase 10 code review of 2026-11-16) fail: the tests were committed, the fixes to `etka_site.py`, `etka_harvest.py`, `etka_…
Verification (1 open, 1 fixed)
- Pick a few well-known circuits (ignition switch, a headlight, CAN to instrument cluster) and check them end to end against the PDF.
The full list, with how each problem was found: docs/known-issues.md in the project. A system hub repeats the open problems that affect its data under “Check first”.