The A4 B6 at launch
What Audi presented as new when the B6 went on sale, from its launch training document SSP 254: dimensions, body and locks.
Audi introduced the B6 A4 (platform 8E) as the “Audi A4 ’01”, and Self-Study Programme 254 (technical status October 2000) is its launch training document. It describes the saloon. The Avant came later, and the S4/RS4 and the B7 facelift are not covered. For model codes and production dates, see Generations and model codes.
What was new
Section titled “What was new”| Area | Highlight in SSP 254 | Article |
|---|---|---|
| Gearbox | The “multitronic” CVT was offered on every front-wheel-drive version, a first in the class | Engines and gearboxes |
| Engines | New 2.0 l four-cylinder (96 kW) and 3.0 l V6 (162 kW) petrol engines with aluminium housings. Both meet EU 4, and SSP 254 credits balancer shafts for their smoothness | Engines and gearboxes |
| Running gear | Four-link front axle with aluminium links and aluminium pivot bearings. The quattro’s trapezium-link rear axle was also used on front-wheel-drive cars | Running gear |
| Safety | Front-airbag crash sensors mounted at the front of the car, plus ESP with a hydraulic brake assistant as standard | Occupant protection, Running gear |
| Aerodynamics | Cd 0.28, about 5 % better than the B5, even with a larger frontal area and the cooling airflow needed for the standard air conditioning | below |
| Electrics | Vehicle electrical system control unit J519, steering column module J527 and a cluster with a built-in CAN gateway | Vehicle electrical system, Instrument cluster |
| Infotainment | Four audio systems, two navigation systems and a voice-operated car phone. The saloon gets the multi-communication bar (aerials in the rear window) | Vehicle electrical system |
Dimensions
Section titled “Dimensions”
Figure: SSP 254
| Dimension (saloon) | mm |
|---|---|
| Length | 4527 |
| Wheelbase | 2650 |
| Front / rear overhang | 921 / 976 |
| Width without / with mirrors | 1766 / 1937 |
| Track front / rear | 1528 / 1526 |
| Height | drawing reads 1628 (see note) |
| Luggage capacity | 445 l |
SSP 254 says that meeting the crash standards made the body heavier, and lighter materials were used to limit the gain:
- More high-strength steel and ten large tailored blanks (pressings welded from sheet of different thicknesses).
- Body rigidity up 45 %, achieved mainly by 25 % more joining points.
- Front structure: straightened longitudinal members with an octagonal, crash-optimised cross-section; a much wider and stiffer bumper cross-member; member structures tied into the passenger cell; and a weight-optimised strut-tower brace.
- Side impact: the floor is made of three large tailored blanks running front to rear, and the sills contain an extruded aluminium profile.
- Doors: one-piece door shell with a bolted-in sub-frame, spray-on sound deadening, and a second weatherseal (one on the door, one on the body). Together these lower interior noise by a further ~3 dB(A).
Aero-floor
Section titled “Aero-floor”Panels cover large parts of the underbody. Besides the drag benefit, they cut noise by about 3 dB(A). The engine-bay sound insulation is a separate part. Audi offset part of the cost by dropping some other panels and the PVC underbody coating, which also helps recycling. The panels are shaped to keep ground clearance, resist stone chips and avoid trapping dirt, stones and snow.
- Boot lid: the lock cylinder sits in the handle. With the cylinder turned horizontal and the key removed, the lid is taken out of the central locking and opens only with the remote’s centre button (“continuous locking”). In the vertical position it is part of the central locking again. Turning the key left unlocks and opens the lid manually. The key can only be removed once the cylinder is back in the vertical position.
- Emergency door locking: if the central locking has no power, each door can be locked individually. With the door open, remove a cap on the door and lock the door using the ignition key in the slot behind it. A door locked this way opens from inside by pulling the release handle twice.
The central locking itself is covered in Convenience system.
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGTechnical status 10/2000. Describes the saloon at launch.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database