Skip to content

Search is only available in production builds. Try building and previewing the site to test it out locally.

Climate control (heater/AC)

The B6 automatic air conditioner as SSP 254 describes it: control head E87, compressors, flap motors and sensors, with the codes the wiring manual uses.

Applies to: B6 onlyVerifiedFrom the factory manual or Audi training material.

Check first

Generated from the wiring data for this system’s 3 diagrams (listed under In the wiring data): the fuses, the ground points and the supply and ground pins of its control modules. These lists are not checked by hand, whatever the article's own status: each line says how it was worked out. Check anything important against the manual sheet before you cut or splice.

Fuses

FuseRatingTerminalWhereFeeds here
S110 A30Panel to 2005 MY: no. 1 p. 1113
Panel from 2006 MY: no. 1 p. 1117
E87 J255
S510 A15Panel to 2005 MY: no. 5 p. 1113
Panel from 2006 MY: no. 5 p. 1117
drawn in this system’s diagrams
S65 A15Panel to 2005 MY: no. 6 p. 1113
Panel from 2006 MY: no. 6 p. 1117
G65 G238
S105 A15Panel to 2005 MY: no. 10 p. 1114
Panel from 2006 MY: no. 10 p. 1118
drawn in this system’s diagrams
S1510 A30Panel to 2005 MY: no. 15 p. 1114
Panel from 2006 MY: no. 15 p. 1118
J285
S88—Fuse Strip (main fuse)drawn in this system’s diagrams
S22530 A30Panel to 2005 MY: no. 25 p. 1114
Panel from 2006 MY: no. 25 p. 1118
J126
S22630 A30Panel to 2005 MY: no. 26 p. 1114
Panel from 2006 MY: no. 26 p. 1118
E87 J9
S24315 A15Panel to 2005 MY: no. 43 p. 1116
Panel from 2006 MY: no. 43 p. 1120
drawn in this system’s diagrams
S24430 APanel to 2005 MY: no. 44 p. 1116
Panel from 2006 MY: no. 44 p. 1120
J255

Ground points

PointWhere
11In battery boxmanual text
12In engine compartment, leftmanual text
18On engine blockmanual text
33Behind instrument panel, rightmanual text
44On left lower A-pillarmanual text
81Splice inside the instrument panel wiring harnesssheet legend
83Splice inside the right front wiring harnesssheet legend
85Splice inside the engine compartment wiring harnesssheet legend
97Splice inside the A/C wiring harnesssheet legend
121Splice inside the right front wiring harnesssheet legend
238Splice inside the wiring harnesssheet legend
244Splice inside the Climatronic wiring harnesssheet legend
261Splice inside the wiring harnesssheet legend
347Splice inside the roof wiring harnesssheet legend
624Near starter batterymanual text
653On left D-pillarmanual text
654On right D-pillarmanual text

Supply and ground pins

Terminal 30 (permanent positive), 15 (ignition), 75 (off while cranking) and 31 (ground) pins of the control modules, from the wire labels. A pin opens its wire, traced to the fuse or ground point; open a module for all its pins.

J9 Rear Window Defogger Relay · 2 pins
PinCarriesWireFuse / ground
2Fused supply from S225 (30 A, terminal 30) to J9 Rear Window Defogger Relayderivedws/geS225 S226
4Ground (terminal 31) at 49 (Near Comfort System Central Control Module)statedbr81
J126 Control module for fresh air blower · 2 pins
PinCarriesWireFuse / ground
3Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr238
4Fused supply from S225 (30 A, terminal 30) to J126 Control module for fresh air blowerderivedro/blS225
J255 Climatronic Control Module · 6 pins
PinCarriesWireFuse / ground
B/14Ground (terminal 31)statedbr/ws97
C/13Load-reduction positive (terminal 75, off while cranking)statedge/sw
D/12Fused supply from S1 (10 A, terminal 30) to J255 Climatronic Control Modulederivedro/blS1
D/13Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr238
D/16Sensor groundstatedbr/ws244
F/3Battery positive, permanent (terminal 30), fused by S226 (30 A, terminal 30)derivedro/wsS226 S244
J285 Control module with indicator unit in instrument panel insert · 4 pins
PinCarriesWireFuse / ground
T32/32Sensor groundstatedbr/ge269
T32a/3Ignition-switched positive (terminal 15)statedswS5 S10 S243
T32a/18Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr135
T32a/19Ground (terminal 31) at 33 (Behind instrument panel, right)statedbr135

The B6’s fully automatic air conditioner is a development of the two-zone system from the A6 (C5).

The operating and display unit E87 is on the convenience CAN and is diagnosed over the K-wire.

New compared with the A6 system:

  • separate temperatures for driver and passenger;
  • holding AUTO for about 3 s copies one side’s temperature to the other;
  • the seat-heating faults and measured values are read under the air conditioner’s address 08;
  • the unit codes itself automatically from the instrument cluster J285;
  • the seat-heating rotary knobs have built-in potentiometers that cannot be replaced separately;
  • the interior temperature sensor G56 and its intake fan V42 are built in and cannot be replaced separately.

SSP 254 lists eight variants, told apart by the part-number index:

  • with or without seat heating;
  • with or without navigation;
  • later also with or without an air-quality sensor.

There are two externally controlled compressors, both governed by the regulating valve N280:

Compressor Plate marking Outside diameter Notes
6-piston 6SEU about 113 mm Covered in SSP 240
7-piston 7SEU about 122 mm More displacement. Used for hot-climate markets. Cars with it get a more powerful radiator fan

Mounting variants:

  • 6- and 7-piston compressor on the right of the engine;
  • 6- and 7-piston compressor on the left;
  • 6-piston only for the V6 TDI.
Function Motor Position feedback
Central flap V70 G112
Air-flow (fresh-air/back-pressure) flap V71 G113
Defrost flap V107 G135
Recirculation flap V113 G143
Temperature flap, left V158 G220
Temperature flap, right V159 G221
Sensor Code
Ambient temperature G17 (SSP 254; not in the database)
Fresh-air intake duct temperature G89
Sunlight photo sensor G107
Vent temperature, left / right G150 / G151
Footwell vent temperature, left / right G261 / G262
Evaporator outlet temperature G263
Refrigerant high-pressure sender G65
Air-quality sensor G238

Signals exchanged with other units:

  • with the engine and gearbox control units: ECON, idle-speed increase and the compressor signal;
  • with the radiator fan control unit J293.

SSP 254’s overview also shows the cluster J285 and the gateway J533 in this network.

SSP 254’s function diagram also shows the heated rear window Z1, the seat heating (Z6/Z8 with seat sensors G59/G60) and the heated windscreen/rear window relay J9.

  • The two sides of the air distribution are separate (driver/passenger).
  • These can be replaced without removing the heater/AC unit:
    • the heater matrix;
    • the PTC auxiliary heater element of diesel models;
    • every flap motor and potentiometer.

A hose from the AC unit feeds cold air into the glovebox. A rotary valve controls the flow. The glovebox holds, for example, a 0.25 l and a 0.7 l bottle.

SSP 254’s performance figures:

  • contents cool from about +30 °C to +16 °C in an hour;
  • with the cold air turned off, they warm by about 4 °C per hour at about 30 °C ambient in sunshine.

Cars without the option have the hose connection closed with a rubber plug.

The solar roof (from the A8/A6) drives the fresh-air blower with sunlight while the car is parked. Blower output rises with sunlight intensity. Compared with the earlier systems:

  • the blower is redesigned;
  • the separate DC/DC converter is gone; its job is done by the blower control unit J126.

SSP 254 lists three benefits:

  • a cooler cabin after parking in the sun;
  • faster cool-down;
  • some de-humidifying in winter.

The solar cells are C20.

Fresh-air blower V2:

  • It has its own control electronics (J126) with fault memory and measured values, diagnosed through E87.
  • It has improved bearings and a separate solar input.
  • E87 calculates the required speed and sends it to J126 as a PWM signal.
  • J126 reports faults such as a stiff or blocked blower back to E87 by changing the duty cycle.

The optional fuel-burning heater warms the coolant, and with it the heater matrix in the AC unit. It works like the earlier systems.

  • Its start time is programmed through the instrument cluster.
  • J393 switches it off after a crash.

SSP 254 calls the heater unit J162. In the 12.2005 manual’s CAN diagrams it appears as J364 “Control module for auxiliary heater”.

In the wiring data

Everything drawn in this system’s diagrams of the factory manual, generated when the site is built. A part drawn in several systems is listed on each of them. Locations say how they were worked out; the component pages have every pin.

Control modules

CodeNameLocationAlso on
J9Rear Window Defogger RelayRelay carrier (9-position) with vehicle voltage control module, from 2006, position 5 (lilac socket) — Behind instrument panel, driver`s side, behind relay carrier (3-position)manual textBasic equipment (J519, J527), Body options
J126Control module for fresh air blowerBehind glove box, in fresh air blower - V2manual text—
J255Climatronic Control ModuleIntegrated with Interior Temperature Sensor Fan -V42- and Instrument Panel Interiormanual textCAN bus and diagnosis, Instrument cluster, Basic equipment (J519, J527), Seats and power mirrors
J285Control module with indicator unit in instrument panel insertBehind display unitmanual textCAN bus and diagnosis, Instrument cluster, Basic equipment (J519, J527), Headlights and auto-dimming mirror, Convenience system, Seats and power mirrors, Body options, Sound system, Navigation and telephone, Airbags and belt tensioners, ABS and ESP, Steering wheel and Servotronic, 1.8 T engine (AMB), 3.0 V6 engine (AVK, BGN), 4.2 V8 engine, S4 (BHF, BBK), 2.0 TFSI engine (BGB, BPG), 3.2 FSI V6 engine (AUK, BKH), 4.2 FSI V8 engine, RS4 (BNS), Automatic gearbox (tiptronic), multitronic gearbox

Other components

Alternator (1)

  • C20 Solar Cells

Battery (2)

  • A Battery
  • A14 Windshield Heating Voltage Converter

Heater (1)

  • Z1 Heated rear window

Ignition switch (1)

  • D Ignition/Starter Switch

Motor (7)

  • V2 Fresh Air Blower
  • V70 Central Air Flap Motor
  • V71 Air Flow Flap Motor
  • V107 Defroster Flap Motor
  • V113 Recirculation Flap Motor
  • V158 Left Temperature Flap Motor
  • V159 Right Temperature Flap Motor

Sensor (15)

  • G65 High Pressure Sensor
  • G89 Fresh Air Intake Duct Temperature Sensor
  • G107 Sunlight Photo Sensor
  • G112 Central Flap Motor Position Sensor
  • G113 Back Pressure Flap Motor Position Sensor
  • G135 Defroster Flap Motor Position Sensor
  • G143 Recirculation Flap Motor Position Sensor
  • G150 Left Vent Temperature Sensor
  • G151 Right Vent Temperature Sensor
  • G220 Left Temperature Flap Potentiometer/Actuator
  • G221 Right Temperature Flap Potentiometer/Actuator
  • G238 Sensor for air quality
  • G261 Left Footwell Vent Temperature Sensor
  • G262 Right Footwell Vent Temperature Sensor
  • G263 Evaporator Vent Temperature Sensor

Solenoid / valve / coil (1)

  • N280 A/C Compressor Regulator Valve

Switch (1)

  • E87 A/C Control Head

Splices

  • A2 Ignition-switched positive (terminal 15)
  • A32 Battery positive, permanent (terminal 30)
  • A33 Load-reduction positive (terminal 75, off while cranking)
  • A38 Ignition-switched positive, fused (terminal 15a)
  • A52 Battery positive, permanent (terminal 30)
  • A57 Battery positive, permanent (terminal 30)
  • A76 K-line (diagnosis)
  • A146 Comfort CAN High
  • A147 Comfort CAN Low
  • B180 Heated rear window
  • B248 Heated Rear Window
  • L31 5 Volts
  • O1 Battery positive, permanent (terminal 30)
  • O2 Ignition-switched positive (terminal 15)

Diagrams

  • 34 Automatic Climate Control (B6 only)
  • 56 Automatic Climate Control (B7 only)
  • 317 Automatic Climate Control (B6 only)

Component locations: A/C

Modify

Understand

Parts in the wiring data

CodeNameModelsLocation
E87A/C Control HeadB6 onlyCentre console, in or at the A/C control head
J255Climatronic Control ModuleB6 and B7Integrated with Interior Temperature Sensor Fan -V42- and Instrument Panel Interior
N280A/C Compressor Regulator ValveB6 and B7Wired into the right front wiring harness
G65High Pressure SensorB6 and B7Wired into the instrument panel wiring harness
G89Fresh Air Intake Duct Temperature SensorB6 and B7Wired into the A/C wiring harness
G107Sunlight Photo SensorB6 and B7Top of the instrument panel
G150Left Vent Temperature SensorB6 and B7Wired into the Climatronic wiring harness
G151Right Vent Temperature SensorB6 and B7Wired into the wiring harness
G238Sensor for air qualityB6 and B7Wired into the instrument panel wiring harness
G261Left Footwell Vent Temperature SensorB6 and B7Footwell, under the instrument panel
G262Right Footwell Vent Temperature SensorB6 and B7Footwell, under the instrument panel
G263Evaporator Vent Temperature SensorB6 and B7Wired into the A/C wiring harness
G112Central Flap Motor Position SensorB6 and B7Part of Central Air Flap Motor -V70-
G113Back Pressure Flap Motor Position SensorB6 and B7Part of Air Flow Flap Motor -V71-
G135Defroster Flap Motor Position SensorB6 and B7Part of Defroster Flap Motor -V107-
G143Recirculation Flap Motor Position SensorB6 and B7Part of Recirculation Flap Motor -V113-
G220Left Temperature Flap Potentiometer/ActuatorB6 and B7Part of Left Temperature Flap Motor -V158-
G221Right Temperature Flap Potentiometer/ActuatorB6 and B7Wired into the A/C wiring harness
V2Fresh Air BlowerB6 and B7The fresh air blower control module -J126- is installed in the fresh air blower -V2-
V70Central Air Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
V71Air Flow Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
V107Defroster Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
V113Recirculation Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
V158Left Temperature Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
V159Right Temperature Flap MotorB6 and B7Shown in the manual's location figures: Components Inside Passenger Compartment
C20Solar CellsB6 and B7Wired into the roof wiring harness
Z1Heated rear windowB6 and B7Rear window
J285Control module with indicator unit in instrument panel insertB6 and B7Behind display unit
J293Coolant FC (Fan Control) Control ModuleB6 and B7On front end, at radiator fan
J364Control module for auxiliary heaterB6 and B7Wired into the instrument panel wiring harness

Sources