B7 multifunction steering wheel
Fitting a B7 multifunction steering wheel and its dual-stage airbag to a B6, condensed from an Audizine write-up, with the factory manual's answer to the airbag question.
What you need
- Tools
- Torx T8 (short, about 6 cm)
- Torx T27
- Torx socket T55
- 4 mm Allen socket
- 10 mm spanner
- Small flat screwdriver
- VCDS (VAG-COM)
- Coding
- Yes: see the coding steps in the article
- Parts
- 4 part numbers in this article, listed below the text
- Wiring
- 5 parts in the wiring data, with their locations and pins
The B7 (from 2005) multifunction steering wheel (MFSW) fits the B6 with a handful of B7/A6 parts. With an RNS-E and the Bluetooth module it lets you scroll the phone book on the DIS, use voice dialling and control the audio from the wheel. This page condenses a well-known Audizine write-up; the original (with photos) is linked under Sources.
What it does
Section titled “What it does”From the original post (RNS-E + Bluetooth car):
| Control | Source | Roll | Press |
|---|---|---|---|
| Left thumb roller | Radio | Scroll stations / presets | Seek |
| CD | Scroll tracks | Fast forward | |
| Bluetooth phone | Scroll the phone’s phone book on the DIS | Dial the shown number | |
| Right thumb roller | All | Volume (radio, CD, phone, navigation) | Repeat the last navigation instruction |
| Mode | All | — | Switch between audio controls and the phone book |
| Speak | All | — | Voice control: dial number, redial, select/store/delete name, play phone book |
| Part | Number | Notes |
|---|---|---|
| Multifunction steering wheel and matching airbag | — | From an A4 B7, A3 or A6 of the same generation. The author paid about US$650 for a used wheel, airbag and harness. |
| Steering column electronics control module | 8E0 953 549 R | J527. Looks identical to the old one: check the sticker on the top edge. |
| Slip ring (clock spring) | 4E0 953 541 B | Has pins in the L-shaped connector that are empty on the B6 slip ring. |
| 4-pin connector housing | 4E0 972 133 | Replaces the yellow connector at the back of the slip ring. |
| Airbag wiring harness | 4F0 971 589 A | Only if it did not come with the airbag. |
Torx T8 (short, about 6 cm), Torx T27, Torx socket T55, 4 mm Allen socket, 10 mm spanner, small flat screwdriver, VCDS (VAG-COM).
Removal
Section titled “Removal”- Read the ABS/ESP coding first. With VCDS, open 03 – ABS Brakes and note the soft coding (the author’s car:
04275). After the battery is disconnected you will need it, and you can’t read it then. - Disconnect the battery (10 mm).
- Put the steering column in its lowest position, pulled fully towards you.
- Turn the wheel to reach the two screws at the back that hold the airbag, and release the airbag.
- Unplug the airbag: pull the yellow tab out first, then the blue connector. Put the airbag down face up.
- Unplug the yellow connector from the slip ring.
- With the steering locked, remove the T55 bolt and mark the column spline so the new wheel goes back in the same position. Pull off the wheel.
- Remove the two T27 screws in the holes under the column cover, then the 4 mm screw under the cover. Separate the upper and lower covers.
- Unclip the three plastic tabs holding the slip ring (small screwdriver), pull it forward and unplug the yellow connector at its back.
- Remove the five T8 screws holding the indicator, cruise-control and wiper stalks: two on the right edge (indicator), one top right (cruise), two on the left edge (wiper). Loosen (don’t remove) the 4 mm screw at the bottom and pull the stalks off as one unit.
- Unplug the steering column control module J527 at the back.
Fitting
Section titled “Fitting”- Re-pin the slip-ring connector. The yellow connector that plugged into the back of the old slip ring is different on the new one. The old housing has a sliding top part that locks the pins; release it, move each wire into the new housing 4E0 972 133 in the same positions, and lock it. Note which wire goes where before you start.
- Fit the new J527 (8E0 953 549 R), the stalks, the new slip ring, the covers and the wheel, in reverse order. Line the wheel up with the mark.
- Connect the airbag (see below) and fit it.
- Reconnect the battery.
The airbag question
Section titled “The airbag question”The factory manual answers what the thread could not:
- The B6 airbag diagram (307) draws only one driver’s airbag igniter, N95. The B6 airbag control module J234 therefore has a single output for the driver’s airbag.
- The B7 airbag diagrams (54, 105) and the B7 multifunction wheel diagrams (72, 112) draw two: N95 and N250 “Driver’s airbag igniter 2”. The same goes for the passenger airbag (N131 and N132).
So the B7 airbag’s second stage has nothing to connect to in a B6. The thread reports two approaches:
- Plug in only the first stage. The author did this and had no airbag warning or fault codes. In a crash, only the first stage would fire.
- Splice the second stage onto the first (“join wire 5 to wire 3 and wire 6 to wire 4”, per another forum member). Nobody had tested what happens in a deployment: both stages might fire together, or neither might.
The proper solution would be a B7 airbag control module and harness, which is a much bigger job. Treat both forum approaches as unverified, and see the warning at the top.
Coding
Section titled “Coding”The ABS/ESP module has to be recoded (and the steering angle sensor calibrated), the airbag fault cleared, and the wheel, RNS-E and DIS may need coding:
- ABS/ESP (03). Log in, enter the coding you noted earlier, and do the steering angle sensor (G85) basic setting. Follow the Ross-Tech procedure for the Bosch 5.7 ABS/ESP. On a car with an unknown brake variant, the author tried the login codes until one was accepted (his:
09575; the calibration itself used40168). Without the calibration the ABS, ESP and brake warnings stay on. - Steering wheel (16). Code it to the car’s options; VCDS shows the choices as a pop-up. The author’s:
04041. It may code itself after the install. - RNS-E (37). Recode for the multifunction wheel. The author’s:
0301715. - Instrument cluster / DIS (17). Adaptation channel 62: add 2 to the value so telephone information shows on the DIS.
- Airbag (15). Clear the stored fault, and check the warning lamp K75 goes out.
For the controller addresses, see VCDS controller addresses.
In the wiring manual
Section titled “In the wiring manual”Shopping list
Every part number in this article. Ticks are kept in this browser for this article only. Check each number against your chassis number before ordering.
8E0 953 549 RSteering column electronics control moduleNot in the loaded part of the catalogue.4E0 953 541 BSlip ring (clock spring)Not in the loaded part of the catalogue.4E0 972 1334-pin connector housingNot in the loaded part of the catalogue.4F0 971 589 AAirbag wiring harnessNot in the loaded part of the catalogue.
The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.
Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J527 | Steering Column Electronic Systems Control Module | B6 and B7 | At steering column |
J234 | Airbag Control Module | B6 and B7 | Below centre console, in front of handbrake lever |
D | Ignition/Starter Switch | B6 and B7 | On the steering column, electrical part of the ignition lock |
K75 | Airbag Malfunction Indicator Lamp (MIL) | B6 and B7 | In the instrument cluster (or in the switch it belongs to) |
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
Sources
- Audizine – B7 Multi-Function Steering Wheel into 2002 Audi A4 (thread, 2007) — HX_Guy and thread participantsPrintout of the first page of the thread (156 posts). The install described is on a 2002 A4 FWD, 5-speed manual, with RNS-E and Bluetooth already fitted.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring databaseAirbag diagrams 307 (B6) and 54/105 (B7); multifunction steering wheel 321 (B6), 72 and 112 (B7), 113 (RS sport wheel).