Drivetrain and convenience CAN (SSP 269)
The two electrically different kinds of CAN in VW and Audi cars of 2000–2005, their signal levels, and the fault-finding procedure, summarised from SSP 269.
This page summarises Self-Study Programme 269. It describes the two electrically different kinds of CAN used by VW and Audi around 2000–2005 and how to find faults on them with the VAS 5051 tester. The SSP is written for the VW Group in general; its examples are a Polo, a Golf IV and a Phaeton. Notes marked On the A4 say where the A4 wiring manual confirms or differs. For the A4’s own bus layout see CAN bus in the A4 B6/B7. For CAN basics see SSP 238.
Two kinds of CAN
Section titled “Two kinds of CAN”| Drivetrain CAN (“high speed”) | Convenience / infotainment CAN (“low speed”) | |
|---|---|---|
| Speed | 500 kbit/s | 100 kbit/s |
| Typical modules | engine, ABS/ESP, gearbox, airbag, dash panel insert | Climatronic/AC, door modules, convenience central module, radio/navigation display |
| Power | switched by terminal 15, with a short run-on | supplied from terminal 30. Goes to sleep mode when not needed after ignition off |
| Message repeat time | typically 10–25 ms | — |
| Load resistors | across High and Low (central ~66 Ω in the engine module) | from each wire to earth or 5 V. Off when unpowered |
| One wire broken or shorted | bus fails | keeps running in single-wire mode |
| Measuring tools | ohmmeter for many faults, scope for some | scope only |
Infotainment and convenience CAN are electrically identical. On some cars (Polo MY2002, Golf IV) they even share one wire pair. On others (Phaeton, Golf V) they are separate.
On the A4 the convenience and infotainment buses are separate pairs: see the buses at a glance.
Wire colours
Section titled “Wire colours”The SSP’s colour rule: CAN wires are orange. CAN-High has a second colour for the bus: black for drivetrain, green for convenience, violet for infotainment. CAN-Low is always orange/brown. Both wires are twisted together (a “twisted pair”) so that interference hits both equally.
On the A4 the wiring manual follows this rule: see Wire colours in the A4 CAN article. In the VAS 5051 scope screens the SSP always shows CAN-High in yellow and CAN-Low in green. Those are screen colours, not wire colours.
VW Group buses use a tree layout: each module hangs off the bus on a short stub, which is unusual for CAN. The actual layout differs from car to car; for the A4 see Topology.
Signal levels
Section titled “Signal levels”Drivetrain CAN
Section titled “Drivetrain CAN”
Drivetrain CAN signal pattern. SSP 269 p. 8 (© Volkswagen AG). Yellow = CAN-High, green = CAN-Low.
| State | CAN-High | CAN-Low | Difference (H − L) |
|---|---|---|---|
| Recessive (rest, logic 1) | ≈ 2.5 V | ≈ 2.5 V | 0 V |
| Dominant (logic 0) | ≈ 3.5 V (at least +1 V) | ≈ 1.5 V (at least −1 V) | ≥ 2 V |
The receiving transceiver uses a differential amplifier: it subtracts Low from High. Interference adds the same voltage to both twisted wires, so the subtraction removes it. Voltage swings in the onboard supply, for example at engine start, are removed the same way. On a real scope trace a module may differ by about 0.5 V from these values. Measure in the middle of a flat part of the pulse, not on the edges.
Convenience / infotainment CAN
Section titled “Convenience / infotainment CAN”
Convenience/infotainment CAN signal pattern. SSP 269 p. 16 (© Volkswagen AG).
| State | CAN-High | CAN-Low |
|---|---|---|
| Recessive (rest) | ≈ 0 V | ≈ 5 V |
| Dominant | ≥ 3.6 V | ≤ 1.4 V |
On this bus High and Low have no common middle voltage. Each wire has its own driver and works as an independent voltage source. That gives a much larger swing: the change from recessive to dominant is at least 7.2 V, against 2 V on the drivetrain bus. It is also what lets the bus survive the loss of one wire.
Load resistances
Section titled “Load resistances”The A4 manual does not show the resistors, so the following VW Group values are not confirmed for the A4:
| Bus | Where the resistors are | What you can measure |
|---|---|---|
| Drivetrain | ~66 Ω “central matching resistor” in the engine control module. ~2.6 kΩ in each other module, all between High and Low | With ignition off, 53–66 Ω between High and Low, depending on how many modules are fitted |
| Convenience / infotainment | In each module, from the wire to earth or to 5 V. Switched off when the module is unpowered | Nothing useful with an ohmmeter |
VW does not use the textbook “one 120 Ω resistor at each end” layout. That makes reflections stronger, which is acceptable on short car harnesses. For the same reason, do not lengthen the drivetrain CAN by more than 5 m, even for testing.
Single-wire mode (convenience / infotainment only)
Section titled “Single-wire mode (convenience / infotainment only)”The low-speed transceiver has built-in fault logic that watches both wires. If one wire is open, shorted to earth, shorted to battery voltage, or shorted to the other wire, the transceiver ignores the bad wire and carries on using only the good one. In a High-to-Low short it switches off its CAN-Low driver. The module reports whether it is in single-wire or two-wire mode. The bus only fails completely when both wires are faulty, or when High and Low are swapped at a module.
Where to start: the gateway
Section titled “Where to start: the gateway”The tester reads the CAN fault entries and measured value blocks from the gateway. In the SSP examples this is address 19, “Diagnosis interface for data bus”. Each module is shown as 1 (communicating), 0 (not communicating) or, on the low-speed bus, “single wire”. In the SSP the blocks from 125 are the drivetrain and the blocks from 130 the convenience bus. The exact layout varies by car, so read the text on the screen.
On the A4 the gateway is the instrument cluster, so these entries and blocks belong to the cluster (SSP 254).
Fault types
Section titled “Fault types”SSP 269 uses the ISO fault chart, plus one fault seen in practice:
| Fault | Description | Drivetrain: found with | Convenience: found with |
|---|---|---|---|
| ISO 1, 2 | Open circuit in CAN-High or CAN-Low | scope | scope |
| ISO 3, 6 | Wire shorted to battery voltage | ohmmeter | scope |
| ISO 4, 5 | Wire shorted to earth | ohmmeter | scope |
| ISO 7 | CAN-High shorted to CAN-Low | ohmmeter | scope |
| ISO 8 | Load resistor missing | scope | does not occur |
| “Fault 9” | High and Low swapped at one or more modules | scope | scope |
Drivetrain CAN procedure (condensed)
Section titled “Drivetrain CAN procedure (condensed)”- Read the fault memory through the gateway.
- If only one module is not communicating: check its connector for bent pins, dirt or corrosion. Then check High and Low to the next module. If it still fails, check that module’s own fault memory (blocks 125–129) and finally replace the module.
- If several modules are affected, or “Drivetrain data bus defective” appears: suspect the wiring. First check with power on whether High or Low is shorted to battery voltage (protect your meter). Then switch terminal 15 off and measure across High and Low:
- 53–66 Ω: resistors and wiring OK. Look for shorts to earth (≤ 300 Ω from either wire to earth) or use the scope.
- ≥ 250 Ω: open circuit. An open branch to the engine module removes the central resistor.
- ≤ 30 Ω: High and Low shorted together.
- Use the scope for open circuits, swapped wires and missing resistors.
On the A4: where to put the meter (diagnostic connector on the B7, the cluster’s green connector on the B6) is in Fault finding in the A4 CAN article.
Convenience / infotainment procedure (condensed)
Section titled “Convenience / infotainment procedure (condensed)”Start with the gateway entries. Use the scope only if the entries do not lead straight to a fixable fault. Use the ohmmeter only to pin down the exact spot, and always with the battery disconnected. Otherwise the bus may wake up and spoil the readings.
Worked examples (condensed)
Section titled “Worked examples (condensed)”Scope settings below are for the VAS 5051 DSO. Channel A = CAN-High, channel B = CAN-Low, scope earth to the nearest earth point.
Drivetrain CAN
Section titled “Drivetrain CAN”| Fault | Tester shows | What the scope shows | Settings | Next steps |
|---|---|---|---|---|
| Open circuit in CAN-Low to the engine module | “Engine control unit — no signal/communication” | CAN-Low sometimes goes above 2.5 V, which never happens normally. With the central resistor cut off, both wires sit near 5 V | A, B 0.5 V/div. 0.05 ms/div. Trigger on B at 3 V; you may need several freeze frames | Check the connector, then the CAN-Low run between the affected module and the modules wired directly to it. For an open CAN-High, the trace folds below 2.5 V; trigger on A at 1.7 V |
| CAN-Low shorted to +12 V (stands for all ISO 3–8 shorts) | Faults stored for all modules, incl. “Drivetrain data bus defective”. Block 125 shows engine/gearbox/ABS all 0 | — | (per fault type) | Check for a short to terminal 30 or 15, look over the harness, unplug modules one by one, then split the bus into sections. Resistance readings say little about where a short is |
| CAN-High and CAN-Low swapped at a module | “… no signal/communication” for that module | CAN-Low partly above the 2.5 V rest level. Error frames | A, B 0.5 V/div. 0.2 ms/div. Trigger on B at 3.25 V | The swap lies between the last working module and the first non-working one. This mostly happens after repairs or new parts are fitted |
Convenience / infotainment CAN
Section titled “Convenience / infotainment CAN”| Fault | Tester shows | What the scope shows | Settings | Next steps |
|---|---|---|---|---|
| Open circuit in one wire to one module | That module “single wire”, the others “1” (example: block 131, “Door RR single wire”) | Hard to see; use the method on the right | — | Earth one wire on purpose. If the affected module then drops out completely (“0”), the break is in the other wire. If everything carries on in single-wire mode, the break is in the wire you earthed. Then ohm out that wire between the affected module and the next working one, battery disconnected |
| CAN-Low shorted to +12 V | “Convenience data bus single wire”. All modules single wire | CAN-Low at battery voltage, CAN-High still signalling | A, B 2 V/div. 0.02 ms/div. Trigger A at 2 V (for High to +12 V: trigger B at 2 V) | Look over the harness, unplug modules one at a time while watching the short on an ohmmeter, then split the harness (e.g. at the door connectors) |
| CAN-High shorted to earth | “Data bus in single wire mode” | CAN-High stays at 0 V, no normal signals | A, B 2 V/div. 0.02 ms/div. Trigger B at 2 V (for Low to earth: trigger A at 2 V) | As above |
| CAN-High shorted to CAN-Low | “Data bus in single wire mode” | Both wires at the same level. The transceiver has switched off CAN-Low | A, B 2 V/div. 0.02 ms/div. Trigger A at 2 V | As above |
| High and Low swapped at one module | That module “no signal/communication” (example: driver door J386) | The rest level moves: High rises, Low falls | A, B 2 V/div. 0.2 ms/div. Trigger B at 2 V | The swap lies between the last working and the first failed module. Check by wire colour, then ohm out, battery disconnected |
On the A4: the door modules and the convenience central module the SSP’s examples use, and the door connectors to split the harness at, are in Fault finding in the A4 CAN article. The door modules are built into the window motors.
OBD access in the SSP
Section titled “OBD access in the SSP”SSP 269 notes that the drivetrain CAN appears on the OBD connector as a “switched” bus, but the VAS 5051 could not use it for measurement. As an alternative it suggests measuring at the dash panel insert’s green connector on the Golf IV and Polo. At the time diagnosis went through the gateway’s K-line (“COM wire”); a dedicated diagnosis CAN was announced for the Touran.
On the A4: which pins of the diagnostic connector and of the cluster carry which bus is in Diagnosis access and Cluster CAN pins.
Related
Section titled “Related”Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
A121 | Wire connection (High-bus), in instrument panel wiring harness | B6 and B7 | Splice inside the instrument panel wiring harness |
A122 | Wire connection (Low-bus), in instrument panel wiring harness | B6 and B7 | Splice inside the instrument panel wiring harness |
A146 | Comfort System High-bus Connection (in instrument panel wiring harness) | B6 and B7 | Splice inside the instrument panel wiring harness |
A147 | Comfort System Low-bus Connection (in instrument panel wiring harness) | B6 and B7 | Splice inside the instrument panel wiring harness |
A178 | Infotainment High-bus Connection (in instrument panel wiring harness) | B6 and B7 | Splice inside the instrument panel wiring harness |
A179 | Infotainment Low-Bus Connection (in instrument panel wiring harness) | B6 and B7 | Splice inside the instrument panel wiring harness |
J386 | Door control module, driver side | B6 and B7 | Integrated in electric window motor |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
Sources
- SSP 269 – Data Transfer on CAN Data Bus II — Audi / VolkswagenTechnical status 04/03. VW Group in general; the worked examples use the Polo, Golf IV and Phaeton.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database — AudiUsed to check the wire colours and the A4 measuring points.