Skip to content

Search is only available in production builds. Try building and previewing the site to test it out locally.

Power-folding mirrors

Fitting S4 power-folding mirrors to a B6: fold-capable front door modules, the mirrors, and the switch with the fold position.

Applies to: B6 onlyCommunity write-upFrom an owner’s write-up or forum thread. Not checked against factory documentation.

What you need

Difficulty
Easy
Coding
None needed
Parts
5 part numbers in this article, listed below the text
Wiring
12 parts in the wiring data, with their locations and pins

The S4 B6 came with power-folding side mirrors (possibly the B7 too), so plug-and-play factory parts exist. These mirrors usually come with auto-dimming glass as well; that may need extra wiring (not verified yet).

Part numbers starting 8E1 are for left-hand-drive cars. For right-hand drive (UK and similar), the numbers are the same with 8E2 instead of 8E1.

Part Left Right Notes
Front door control module 8E1 959 801 8E1 959 802 Suffix E or G also work; B and H do not.
Mirror assembly 8E1 858 531 AC 8E1 858 532 AC
Mirror switch with fold function 8E0 959 565 A Replaces the plain adjustment switch E43 with E168.

On this car the mirrors are not wired to the switch. They hang on the front door control modules, J386 (driver) and J387 (passenger), which are built into the window motors. The switch only sends its position to J386, which then drives the mirror motors, the heater and the fold motor. The two door modules talk to each other and to the comfort module over the comfort CAN bus (or/gn and or/br on pins 4 and 5 of the 10-pin connector T10e).

So folding needs:

  1. door modules with a fold output: not every J386/J387 version drives the fold motor, hence the suffix list above;
  2. mirrors with the fold motors V121 (driver) and V122 (passenger);
  3. the switch with the fold position, E168 “switch for mirror adjustment with fold-away function”. In the manual its fold contact runs on its own wire, bl/gr, to J386 T32c/22.

Wiring at the door module (driver’s side)

Section titled “Wiring at the door module (driver’s side)”

The mirror plugs into J386’s 16-pin connector T16b. From the factory manual (comfort diagrams 6, 35, 318):

T16b pin Manual: connects to
1 Mirror adjustment motor V149 (left/right)
2 Mirror adjustment motor V17 (up/down)
3 V17, common
4 shared by the mirror heater Z4 and the fold motor V121
5, 6 Mirror heater Z4
9 shared by V149 and the fold motor V121
10 Fold motor V121
13, 14, 15, 16 further connections to V149 and V17 (the manual does not name them; on memory mirrors these are likely the position sensors)

The owner’s own (work-in-progress) pinout of T16b has the fold motor on pins 9 and 10, which fits this. On a car without folding mirrors, pins 9 and 10 may be empty in the harness. The new mirror’s harness brings its own wires, which is why the procedure below replaces the mirror cable through the door.

Fairly straightforward:

  1. Remove the door panels.
  2. Swap the door control modules (they come off with the window regulator motors).
  3. Pull the old mirror cable out of the door and route the new mirror’s cable in.
  4. Fit the mirrors and the new switch.

No coding should be needed: the fold-capable door modules handle it on their own.

  • Whether the auto-dimming function of the S4 mirror glass needs extra wiring, and where it would come from. In the factory wiring the auto-dimming interior mirror Y7 talks to the door modules over pins 7 and 8 of T10e.
  • Whether the same swap works on a B7, and with which door-module numbers.

Shopping list

Every part number in this article. Ticks are kept in this browser for this article only. Check each number against your chassis number before ordering.

  • 8E1 959 801 Front door control module
    Not in the loaded part of the catalogue.
  • 8E1 959 802 Front door control module
    Not in the loaded part of the catalogue.
  • 8E1 858 531 AC Mirror assembly
    Not in the loaded part of the catalogue.
  • 8E1 858 532 AC Mirror assembly
    Not in the loaded part of the catalogue.
  • 8E0 959 565 A Mirror switch with fold function
    Not in the loaded part of the catalogue.

The catalogue on this site is incomplete: of the B6 catalogue only main groups 1 Engine (101 illustrations) and 4 Front axle, steering (3 illustrations) are loaded; nothing of the B7 catalogue is loaded.

Parts in the wiring data

CodeNameModelsLocation
J386Door control module, driver sideB6 and B7Integrated in electric window motor
J387Door control module, passenger sideB6 and B7Integrated in electric window motor
V121Motor for fold-in mirror, driver sideB6 and B7In the driver's outside mirror
V122Motor for fold-in mirror, passenger sideB6 and B7In the front passenger's outside mirror
E168Switch for Mirror Adjustment with Fold-Away FunctionB6 and B7—
E43Mirror Adjustment SwitchB6 and B7Driver's door trim, mirror switch
Z4Heated outside mirror, driver sideB6 and B7In the driver's outside mirror
Z5Heated outside mirror, passenger sideB6 and B7In the front passenger's outside mirror
V17Driver's Side Mirror Adjustment MotorB6 and B7In the driver's door
V149Driver's Side Mirror Adjustment MotorB6 and B7In the driver's door
V25Passenger's Side Mirror Adjustment MotorB6 and B7In the front passenger's door
V150Motor for mirror adjustment, passenger sideB6 and B7In the front passenger's outside mirror

Sources