Skip to content

Search is only available in production builds. Try building and previewing the site to test it out locally.

C24 · Suppressor

Name
Suppressor
Type
alternator
Models
B7 only
Diagrams
1

Location

The manual does not say where this part is.

Pins

One row per pin and wire colour; the pin opens the page of its wire, traced across every sheet. "Connects to" lists the other pins on the same circuit within a diagram; splices and ground points it passes are under "via". The function says how it was worked out: stated by the manual, derived from terminal markings, fuses or the colour code. "Not stated" means the manual only shows what the wire connects.

T1h · 1-Pin Connector, on Suppressor likely Switches

T1h · 1-Pin Connector, on Suppressor · diagram 95

Pin positions schematic: check the numbers moulded on the housing

Pins printed with a label that is not a position number from 1 to 1: their place on the housing is not known.

1 positions (sheet legend), pin 1 top left, then in number order. The manual does not give the housing shape, its keying or how the pins sit in rows. A dashed cell is a position with no wire in the extracted sheets: that does not mean it is empty in the car. Tap a pin for its function, far ends and wire.

Dimmed: pins drawn only in diagrams that do not apply to the car set in “My car”.

Tap a pin for what it does and where its wire goes.

T1h pin 1

No wire on this position in the wiring data. The extracted sheets draw only what each circuit uses, so the position may still be used in the car: check before relying on it.

T1h pin ?

Colour
sw/ro 0.35 mm²
Function
Starter control (terminal 50)stated
Far ends
C24, D/5/50b, J623/10
via D97
Wire
Starter control (terminal 50)
Diagrams
95

Row in the pin table

PinWireFunctionConnects toModelsSheets
?
sw/ro 0.35 mm²
Starter control (terminal 50)stated
C24, D/5/50b, J623/10
via D97
B7 only569

T1j · 1-Pin Connector, on Suppressor likely Sensors

T1j · 1-Pin Connector, on Suppressor · diagram 95

Pin positions schematic: check the numbers moulded on the housing

Pins printed with a label that is not a position number from 1 to 1: their place on the housing is not known.

1 positions (sheet legend), pin 1 top left, then in number order. The manual does not give the housing shape, its keying or how the pins sit in rows. A dashed cell is a position with no wire in the extracted sheets: that does not mean it is empty in the car. Tap a pin for its function, far ends and wire.

Dimmed: pins drawn only in diagrams that do not apply to the car set in “My car”.

Tap a pin for what it does and where its wire goes.

T1j pin 1

No wire on this position in the wiring data. The extracted sheets draw only what each circuit uses, so the position may still be used in the car: check before relying on it.

T1j pin ?

Colour
br 0.5 mm²
Function
Ground (terminal 31) at 12 (In engine compartment, left)stated
Far ends
C24, F1/1, G266/2/31, J623/1, J623/2, J623/4, N292/2, N323/2, N324/2, V274/1, V51/2
via 12, 83, 121
Wire
Ground (terminal 31) at 12 (In engine compartment, left)
Diagrams
95

Row in the pin table

PinWireFunctionConnects toModelsSheets
?
br 0.5 mm²
Ground (terminal 31) at 12 (In engine compartment, left)stated
C24, F1/1, G266/2/31, J623/1, J623/2, J623/4, N292/2, N323/2, N324/2, V274/1, V51/2
via 12, 83, 121
B7 only569

Diagrams

From the factory manual Audi A4 Wiring Diagrams and Component Locations, edition 12.2005, extracted automatically. Check anything important against the PDF sheet.