Immobiliser (IMMO3 and IMMO4)
Stub. The immobiliser sits in the instrument cluster and reads the key through coil D2. Which generation each car has is disputed for the B7.
What this page will cover
Section titled “What this page will cover”How the immobiliser recognises the key, what it exchanges with other modules, the differences between Immo 3 (B6) and Immo 4 (B7), and what is needed to repair or replace a cluster, at the level that legitimate repair and integration need.
What the sources in this repo already say
Section titled “What the sources in this repo already say”- SSP 254 states that the B6 launch cluster contains immobiliser III, reads the key through the coil D2 around the ignition lock, and exchanges data with the convenience control unit J393 over the convenience CAN (Instrument cluster).
- In the wiring manual the coil is connected to the cluster at T32 pins 30 (transponder 2, to D2 pin 2) and 31 (transponder 1, to D2 pin 1); the B7 standard-equipment diagrams keep the immobiliser coil on T32/30–31 (Instrument cluster).
- The owner’s notes give Immo 3 with the Bosch RB4 cluster on the B6 and Immo 4 with the RB8 on the B7. B6 vs B7 electrical differences collects forum reports that some B7 clusters are Immo 3. The two articles disagree; both are kept, and the generation can be read from the cluster with VCDS.
- On both generations the immobiliser is part of the cluster (address 17); there is no separate address 25 (VCDS controller addresses).
- A used cluster from another car will not simply plug in; an Immo 3 RB4 and an Immo 4 RB8 are not interchangeable without adaptation work (Instrument cluster).
- The alarm triggers if the key used is not stored in the immobiliser (Convenience system and anti-theft alarm).
Open questions
Section titled “Open questions”- Which immobiliser generation does each B7 cluster (by part number, build date, equipment) have? Which VCDS output shows it?
- What is exchanged over the convenience CAN between the cluster and J393: which messages, how often, and in which ignition states?
- For repair: how can a faulty coil D2 or a fault in its wiring to T32/30–31 be told apart from a faulty key or a faulty cluster, with a multimeter or an oscilloscope? What resistance should the coil show, and which fault codes point to it?
- How is the immobiliser linked to the engine control module on each generation, and over which bus?
- Which adaptation channels and measuring blocks of address 17 relate to the immobiliser? The VCDS controller addresses page lists channels 060–062 and 099 only in general terms.
- Does phone-based locking need anything from the immobiliser? The working assumption is not, but nothing in the repo shows this.
How to capture or measure it
Section titled “How to capture or measure it”- Read-only first: VCDS address 17, identification screen and measuring blocks. Write down part numbers, coding and any immobiliser-related text, with the date.
- Passive listening on the convenience CAN with the ignition key out, in and turned to on, at a known splice (A146/A147, or the cluster’s blue T32 pins 17 and 18). Log with timestamps.
- Do not code, adapt or learn keys while investigating, and do not transmit on the bus.
Related
Section titled “Related”Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
D2 | Induction Coil of Anti-theft Immobilizer | B6 and B7 | Steering column, around the ignition lock |
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 40–43: immobiliser III integrated in the cluster, reads the key through the coil, exchanges data with J393.
- Ross-Tech Wiki – Immobilizer — Ross-TechVia the Instrument cluster article: immobiliser generations 3 and 4.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database — AudiCluster connector pins T32/30 and T32/31 to coil D2.