Central locking and alarm
Stub. J393 and the door control units run locking and the alarm over the convenience CAN. The messages between them are not yet documented.
What this page will cover
Section titled “What this page will cover”The path from a lock or unlock request (remote key, lock cylinder, interior switch) through J393 and the door control units to the lock motors, the alarm’s states, and the convenience-CAN messages that carry all of this.
What the sources in this repo already say
Section titled “What the sources in this repo already say”All from Convenience system and anti-theft alarm (SSP 254, B6) unless stated.
- The central convenience control unit J393 and one door control unit per door (J386 driver, J387 passenger, J388 and J389 rear, optional) talk over the convenience CAN. The door control units are built into the window motors.
- Each door control unit has locking, unlocking and safe (deadlock) outputs and takes lock feedback (door contact, locked, safe). The driver’s door also takes the lock-cylinder switch F241 and the interior central-locking switch.
- Without rear electric windows, J393 itself runs central locking for the rear doors.
- Inputs to J393 include the remote aerial R47, the crash signal from the airbag control unit (J393 then unlocks the car), the bonnet switch F266 and the handbrake switch.
- Alarm: arms only when the car is locked with the remote and the driver’s door is closed; disarms on unlock with the remote, or with the key in the driver’s door lock if the ignition is switched on within 15 s; triggers if the 15 s pass or the key is not known to the immobiliser. The sounder has its own battery. The interior monitor and towing protection can be switched off with an interior switch.
- Alarm flashing is sent over CAN to J519, which flashes the turn signals.
- J393 is a diagnosis gateway for J519 and J527. In VCDS, central convenience is address 46 (VCDS controller addresses).
- The comfort-system diagrams for the B7 differ from the B6; SSP 254 describes the B6 only, so the page’s generation is B6 until the B7 is checked.
Open questions
Section titled “Open questions”- Which convenience-CAN message tells the door control units to lock, unlock or deadlock, and who sends it?
- Which messages report each door’s lock state and open/closed state to the rest of the bus?
- Is there a separate message for the driver’s door only (single-door unlock) versus all doors?
- Which message arms or disarms the alarm, and what shows the alarm state on the bus?
- What happens to the alarm if the doors are locked by a CAN message instead of the remote? SSP 254 says it arms only when locked with the remote. Does the unlock-with-remote rule have a CAN equivalent?
- Does the bus have to be awake to send a lock command, and what wakes it (see Convenience CAN messages)?
- Are the B7 messages the same as the B6 ones?
How to capture or measure it
Section titled “How to capture or measure it”- Passive listening on the convenience CAN at the splices A146/A147 (listen-only, 100 kbit/s), logging while doing one thing at a time: lock and unlock with the interior button, with the key in the driver’s door, with the remote; open and close each door; arm and disarm the alarm. Write down times and ignition state.
- Read-only VCDS: address 46 measuring blocks (door contact, lock state) at the same moments, so the log can be tied to the car’s own view.
- Do not transmit on the bus. Never connect the convenience bus to another CAN bus.
Related
Section titled “Related”Parts in the wiring data
| Code | Name | Models | Location |
|---|---|---|---|
J393 | Central control module for comfort system | B6 and B7 | At sill panel, front left |
J386 | Door control module, driver side | B6 and B7 | Integrated in electric window motor |
J387 | Door control module, passenger side | B6 and B7 | Integrated in electric window motor |
J388 | Door control module, rear, left | B6 and B7 | Integrated in electric window motor |
J389 | Door control module, rear, right | B6 and B7 | Integrated in electric window motor |
R47 | Central Locking and Anti-theft Alarm System Antenna | B6 and B7 | Routed from the Comfort System Central Control Module -J393- |
J285 | Control module with indicator unit in instrument panel insert | B6 and B7 | Behind display unit |
J519 | Vehicle Electrical System Control Module | B6 and B7 | Behind driver's storage compartment |
H12 | Alarm Horn | B6 and B7 | In luggage compartment, right, behind side trim |
F266 | Front Hood Switch | B6 and B7 | In lock carrier |
G303 | Radar Interior Monitoring Control Module 1 | B6 and B7 | Wired into the roof wiring harness |
E183 | Switch for passenger compartment monitoring | B6 and B7 | Wired into the driver's door wiring harness |
F241 | Contact switch for lock cylinder, driver side | B6 and B7 | Integrated in driver and passenger door lock |
Sources
- SSP 254 – Audi A4 '01 Technical Features — Audi AGPages 11 and 58–64: J393, door control units, the alarm. Describes the B6 only.
- Audi A4 Wiring Diagrams and Component Locations (12.2005), via the wiring database — AudiComfort-system diagrams 318, 6 and 35 (B6) and 67 and 110 (B7).